Manual Lavorwash STM 160 Kit 2 (page 10 of 136) (All languages)

733407

Zoom out

Zoom in

1/136

 XY WARNING: Inadequate extension cords

can be dangerous.

 XJ WARNING: If an extension cord is used,

the plug and socket must be of watertight

construction.

Information for supply may also be obtained

from the plug manufacturer.

<16 A <25 A

<20 m ø 1,5 mm

14 AWG

ø 2,5 mm

12 AWG

20 m - 50 m ø 2,5 mm

12 AWG

ø 4,0 mm

10 AWG

> PLUG

HOW TO CONNECT THE CORD TO A U.K. PLUG:

IMPORTANT The wires in the mains lead are

coloured in accordance with the following

code:

Blue Neutral

Brown Live

Yellow/Green Earth

Please read the in-

structions given

below before con-

necting the cord to

a plug. If in doubt

please consult a

qualiﬁed electri-

cian. As the colours

of the wires in the

mains lead of this

appliance may not

correspond with

the coloured mark-

ings identifying the

terminals in your plug, proceed as follows:

The wires that is coloured Brown must be con-

nected to the terminal which is marked with

the letter L or coloured Red. The wire that is

coloured Blue must be connected to the ter-

minal which is marked with the letter N or col-

oured Black.

Safety points for rewireable or moulded plug:

The mains lead of this appliance may be already

fitted with a BS1363 13A plug.

- If your socket outlet is not suitable for the

plug, then the plug must be removed (cut

off if it is a moulded on plug), the flexible

cord insulation should be stripped back as

appropriate and a suitable 3 pin plug fitted.

 WARNING: Dispose of a plug that has been

cut from the power supply cord, as such

a plug is hazardous if inserted in a live 13A

socket outlet elsewhere in the house.

- Should the fuse need to be replaced an ASTA

marked fuse, approved to BS1362, of the

same rating must be used.

- Always replace the fuse cover after fitting

a fuse. The plug must NOT be used if the

cover is omitted or lost until a replacement

is obtained.

- Make certain that only the correct fuse cover

is used and fitted.

- For plugs with detachable fuse cover the

replacement must be the same as the colour

insert in the base of the plug, or as directed

by the embossed wording on the base of the

plug.

- If the detachable fuse cover is lost a

replacement may be purchased from a

Service Centre.

( if fitted)

NOTE: (Automatic Stop System),

which stops the machine during the

bypass phase. To start the water cleaner, it

is therefore necessary to set the switch on

position (I)“ON”; after that press the pistol

trigger: the Automatic Stop System will start

the machine and will stop it automatically

when the trigger is released. It is advisable

to put on the safety of the pistol trigger

whenever the machine is stopped, in order

to avoid unintentional starting.

· Any automatic start of the machine without

pressing the gun trigger is attributable to

air bubbles in the water or other similar

phenomena which do not imply the

existence of any defects in the machine.

· Do not leave the appliance unattended

during the standby for more than 5 minutes.

Contrarily, for the safety of the appliance it

is necessary to re-turn the switch into the (0)

OFF position.

· Please check that the coupling of the high

pressure hose with the appliance and the

gun supplied as standard equipment made

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Lavorwash STM 160 Kit 2 in the language / languages: All languages as an attachment in your email.

The manual is 3,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Lavorwash STM 160 Kit 2 Manual

Product: