733407

Lavorwash STM 160 Kit 2 Manual

9
Zoom out
Zoom in
Previous page
1/136
Next page
EN
9
the product to the electric system. In case
this problem repeats again or if the product
does not start again, take the product to the
nearest After Sales Service Point
> STABILITY
WARNING:
The machine must be always kept
on horizontal bases, in a safe and stable way.
USAGE
> DESCRIPTION OF THE MACHINE
See the specific instructions manual
provided.
> ASSEMBLY INSTRUCTIONS
See the specific instructions manual
provided.
> PUT INTO SERVICE
See fig.
> STARTING UP
See fig.
> HIGH PRESSURE LANCE
See fig.
> DETERGENT SUCTION
See fig.
- -
> HIGH PRESSURE HOSE
See fig.
> WATER SUPPLY
Water supply collection
Water supply from the water main
· Connect a supply hose (not included) to
the water inlet of the unit and to the water
supply.
· Open the water supply.
WARNING: (symbol) machine not suitable
for connection to the potable water mains.
The cleaner can only be connected to the wa-
ter mains if the water mains is separated by a
backflow preventer. Make sure that the hose
is at least Ø 13mm-1/2 inch and that it is rein-
forced.
WARNING: Water that has flown through
backflow preventers is considered to be
nonpotable.
IMPORTANT: Only clean or filtered water
should be used for intake. The delivery of
the water intake tap should be equal to the
double of the maximum pump range.
- Minimum delivery rate: 15 l/ min.
- Maximum intake water temperature: 40°C
- Max inlet water pressure: 1Mpa
Place the cleaner as close to the water supply
system as possible.
Water supply from an open container
· Unscrew the coupling part for the water
inlet.
· Screw the suction hose with filter (not
included) onto the water connection of the
unit.
· Hang the filter in the container.
· Vent the unit before operation.
· Unscrew the high-pressure line at the high-
pressure outlet of the unit.
· Switch on the unit and let it run until water
free of bubbles emerges at the high-pressure
outlet.
· Switch off the unit and screw on the high-
pressure hose again.
Failure to comply with the above conditions
causes serious mechanical damage to the
pump and the loss of warranty cover.
> ELECTRICITY SUPPLY
- The appliance’s electrical connection must
comply with the IEC 60364-1 standard.
IMPORTANT:
Before connecting the
appliance, make sure that the nameplate
data are the same as those of the electrical
mains and that the socket is protected by a
differential security breaker with tripping
sensitivity below 0.03 A - 30 ms.
- If the appliance’s plug is not compatible with
the socket, have the socket replaced with
another of suitable type by professionally
qualified staff.
- Never use the appliance in ambient
temperatures below 0° C if it is equipped
with a PVC (H VV-F) cable.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lavorwash STM 160 Kit 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lavorwash STM 160 Kit 2 in the language / languages: All languages as an attachment in your email.

The manual is 3,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info