495522
15
Zoom out
Zoom in
Previous page
1/36
Next page
Maintenance manual for technical assistance - LB 2800 - LB 2810
Manual code 10066574 / Rel. 0.00 / March 2009
11
3.4. Water connection
Inlet and outlet water connections should comply
with applicable laws in force in the country where
the machine is used.
- connect the water mains (2) to the inlet on the back
of the machine (6) using the hose provided. Then
open the tap of the water mains.
- connect the drain tub of the machine (4) to the sewer
drain (3) using the special tube provided. Take care to
avoid overly tight bends or kinks, and make sure that
there is sufficient inclination for water to flow out of
the drain..
Warning
Check that the surface prepared for the machine
installation, has dimensions and sturdiness suitable
to safely support the machine.
Note
F
or a correct ergonomic use of the machine, place
it on a working surface not lower than one meter
from the floor.
Warning
For correct operation, the machine must rest on a
perfectly horizontal surface. Any alignment adju-
stments of the machine must be done by adjusting
the feet.
Note
All filling connections are 3/8 male gas type. The
drain tub is connected with a tube with an internal
diameter of 16mm.
W
arning
Insert a tap (8) and a non-return valve (9)on the
water mains supply so that it will be possible to cut
off water flow to the machine.
Connect the water mains (2) directly to the inlet of
the machine (6). If you decide to install a water sof-
tener (11), connect the water mains (2) to the inlet
of the water softener, and the outlet of the water
softener to the inlet of the machine (6).
To prevent the water from freezing, install the sof-
tener (11), only in rooms with an ambient tempera-
ture of more than 5°C.
When connecting the tub of the machine to the
sewer drain, avoid overly tight curves or kinks, and
make sure that there is sufficient inclination for
water to flow out of the drain.
The drain must be connected to an inspectionable
siphon that can be periodically cleaned in order to
avoid the backflow of unpleasant odours.
To avoid oxidization and damage to the machine
over time, do not use iron connections for the
hydraulic connections, even if they are galvanized.
Attention
The hydraulic connection must be made in com-
pliance with local national standards.
If an external tank is used, the connection pipe
between the machine and the tank must not
exceed 150 cm.
For the European Community: for both the
hydraulic connection to the water mains as well
as the connection to an external tank, a non-
return valve (9) must be placed up the line from
the machine as set forth by standards EN 1717.
Warning
The water mains must provide cold water for
human consumption (potable water) at a maximum
pressure of 5 bar inclusive If the pressure is greater
than 5 bar, connect a pressure reducer upstream
from the pump.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lavazza LB 2810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lavazza LB 2810 in the language / languages: English as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info