646815

Laserliner ThermoSpot Plus Manual

8
Zoom out
Zoom in
Previous page
1/92
Next page
5
6
...
E 0.01...1.00
08
GB
Alloy A3003
Oxidised
Roughened
0.3
0.1 - 0.3
Aluminium
Oxidised
Polished
0.2 - 0.4
0.04 - 0.06
Brass
Polished
Oxidised
0.3
0.5
Copper
Oxidised
Elect. terminal strips
0.4 - 0.8
0.6
Haynes
Metal alloy
0.3 - 0.8
Inconel
Oxidised
Sandblasted
Electropolished
0.7 - 0.95
0.3 - 0.6
0.15
Iron
Oxidised
With rust
With red rust
0.5 - 0.9
0.5 - 0.7
0.61 - 0.85
Iron, cast
Oxidised
Non-oxidised
Molten mass
0.6 - 0.95
0.2
0.2 - 0.3
Iron, forged
Matt
0.9
Lead
Rough
Oxidised
0.4
0.2 - 0.6
Molybdenum
Oxidised
0.2 - 0.6
Nickel
Oxidised
0.2 - 0.6
Platinum
Black
0.9
Steel
Cold rolled
Ground plate
Polished plate
Alloy (8% nickel,
18% chromium)
Galvanised
Oxidised
Heavily oxidised
Freshly rolled
Rough, flat surface
Rusty, red
Sheet, nickel plated
Sheet, rolled
0.7 - 0.9
0.4 - 0.6
0.1
0.35
0.28
0.80
0.88
0.24
0.95 - 0.98
0.69
0.11
0.56
Zinc
Oxidised
0.1
Setting the emission coefcient
Table of emission coefcients
A built-in sensor head detects the material/surface-specic infrared rays emitted by every object. The level of
these emissions is determined by the material‘s emission coefcient (0.01 to 1.00). After switching on for the
rst time, the device is preset to an emissivity coefcient of 0.95, which is suitable for most organic materials
as well as plastics, ceramics, wood, rubber and stone. For materials with different emissivity coefcients,
please refer to the table under point 6.
Unknown emission coefcient:
Apply masking tape or black matt paint to the surface of the area whose temperature you wish to measure.
Wait until the tape/paint has heated up. The temperature of the surface can then be measured with an
emission coefcient of 0.95.
Button pressed briey: Value +0.01
Keep button pressed:
Value runs through 0.01 … 1.00
Metals
The emissivity coefficient last selected is set after the device is switched on. Check the emissivity
coefficient setting before each measurement.
!
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner ThermoSpot Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner ThermoSpot Plus in the language / languages: All languages as an attachment in your email.

The manual is 6,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info