646089

Laserliner SuperCross-Laser 3 Manual

9
Zoom out
Zoom in
Previous page
1/60
Next page
ENGLISH 9
SuperCross-Laser SCL 3
Technical Data
Automatic levelling range ± 5°
Accuracy ± 5 mm / 10 m
Operating range (depending on room illumination) 20 m
Laser wavelength
635 nm
Laser class / line laser output power 2M / < 5 mW
Power supply
4 x 1,5V AA / ca. 20 h
Dimensions / weight (without wall bracket and batteries) 122 x 100 x 70 mm / 0,55 kg
Temperature range, operating / storage 0°C ... +50°C / -10°C ... +70°C
Order number 081.140A
Subject to technical changes without notice 04/2009
Horizontal and vertical levelling:
Open the battery compartment (2) and insert batteries according to the symbols. Correct polarity
must be observed. Release the transport restraint, put the ON/OFF switch (4) into its right position
("ON" ). Now the tilt function is active and the indicator LED (11) will light up green if the device is
set up correctly. The desired laser lines can be selected with the selection button (5). The indicator
LED (11) will light up red if the device is tilted too much, such that the pendulum is out of its self-
levelling range. There will also be a warning sound and the lasers will blink. The unit must then be
placed on a surface which is closer to level. Refer to the application examples in Figures A, B, C on
page 2.
Slope mode:
Do not release the transport restraint, put the ON/OFF switch into its left position ("OFF"). Now the
tilt function is inactive! Select and switch on the laser with the selection button (5). Now the indica-
tor LED (11) will light up red and the device can be placed on sloped or tilted surfaces. Refer to the
application example in Figure D on page 2. IMPORTANT: This mode cannot be used to perform
horizontal or vertical levelling because the laser lines are no longer automatically aligned.
Note: Regularly check the calibration before use, after transport and after extended periods of
storage.
Anleit_SCL-3_Rev.0409_A:Layout 1 16.04.2009 16:02 Seite 9
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner SuperCross-Laser 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner SuperCross-Laser 3 in the language / languages: All languages as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info