646090

Laserliner SuperCross-Laser 2P RX Set 150 Manual

9
Zoom out
Zoom in
Previous page
1/92
Next page
SuperCross-Laser 2P
9
GB
Performing the calibration check:
Preparing the calibration check:
It is possible for you to check the calibration of the laser. To do this, position the device midway between 2 walls,
which must be at least 5 metres apart. Switch the device on (Laser cross ON). The best calibration results are achie-
ved if the device is mounted on a tripod.
A1
A2
2.
1.
A3
A2
A2
A1
4.
3.
A3
A2
<
2 mm / 10 m = OK
If points A2 and A3 are more than 5 mm / 10 m, the device is in need of calibration. Contact your authorised
dealer or else the UMAREX-Laserliner Service Department.
!
1. Mark point A1 on the wall.
2. Turn the device through 180° and mark
point A2. You now have a horizontal
reference between points A1 and A2.
3. Position the device as near as possible to
the wall at the height of point A1.
4. Turn the device through 180° and mark
point A3. The difference between points
A2 and A3 is the tolerance.
Checking the vertical line: Position the device about 5 m from a wall. Fix a plumb bob with a line of 2.5 m
length on the wall, making sure that the bob can swing freely. Switch on the device and align the vertical laser to the
plumb line. The precision is within the specified tolerance if the deviation between the laser line and the plumb line is
not greater than ± 1.5 mm.
Checking the horizontal line:
Position the device about 5 m from a wall and switch on the cross laser. Mark point B
on the wall. Turn the laser cross approx. 2.5 m to the right and mark point C. Check
whether the horizontal line from point C is level with point B to within ± 2 mm.
Repeat the process by turning the laser to the left.
B
C
2,5 m
< 2 mm = OK
Regularly check the calibration before use, after transport and after extended periods of storage.
!
02_Manual_SCL_2P_Rev1110_GB.indd Abs1:9 24.11.2010 11:01:32 Uhr
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner SuperCross-Laser 2P RX Set 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner SuperCross-Laser 2P RX Set 150 in the language / languages: All languages as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info