646095

Laserliner SmartCross-Laser Set 150 cm Manual

6
Zoom out
Zoom in
Previous page
1/68
Next page
6
3
A1
A2
2.
1.
A3
A2
A2
A1
4.
3.
A3
A2
<
0,5 mm / m = OK
LASER LASER LASER LASER
GB
Slope mode
Do not release the transport restraint, set the ON/OFF switch to „OFF“. Select and switch
on the laser with the selection button. Sloping planes can now be measured. This mode
cannot be used to perform horizontal or vertical levelling as the laser lines are no longer
aligned automatically. The LED lights constantly red.
Technical data
Self-levelling range ± 5°
Accuracy ± 0.5 mm / m
Operating range
(depending on room illumination)
10 m
Laser wavelength 650 nm
Laser class / line laser output power 2 / < 1 mW
Power supply
2 x 1.5V alkaline batteries
(type AA, LR6)
Operating time 15 hours (alkaline batteries)
Operating temperature 0 °C ... +40 °C
Storage temperature -10 °C ... +70 °C
Dimensions (W x H x D) 55 x 85 x 75 mm
Weight (incl. batteries) 260 g
Guarantee, product care and disposal
This device complies with all necessary standards
for the free movement of goods within the EU.
This product is an electric device and must be collected separately
for disposal according to the European Directive on waste electrical
and electronic equipment.
Further safety and supplementary notices at:
www.laserliner.com/info
Performing the calibration check
3. Position the device as near as possible to the wall at the height of point A1.
4. Turn the device through 180° and mark point A3. The
difference between points A2 and A3 is the tolerance.
Preparing the calibration check
It is possible for you to check the calibration of the laser. To do this, position the device
midway between 2 walls, which must be at least 5 metres apart. Switch the device on
(LASER CROSS ON). The best calibration results are achieved if the device is mounted
on a tripod.
1. Mark point A1 on the wall.
2. Turn the device through 180° and mark point A2. You now have a horizontal
reference between points A1 and A2.
If points A2 and A3 are more than 0,5 mm / m, the device is in need of
calibration. Contact your authorised dealer or else the UMAREX-LASERLINER
Service Department.
!
Subject to technical alterations. 02.13
Manual_SmartCross-Laser_Rev.0213.indd 06 19.02.13 07:41
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner SmartCross-Laser Set 150 cm at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner SmartCross-Laser Set 150 cm in the language / languages: All languages as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info