694703

Laser 5089 Manual

10
Zoom out
Zoom in
Previous page
1/18
Next page
Laser 5089 Code Reader User’s Guide_ Laser 5089 Code Reader User’s Guide_
Diagnostic Menu allows you to:
• Read DTCs.
• Clear DTCs.
• View live datastream.
• View freeze data.
• Retrieve vehicle information.
√ The code reader detects the communication protocol when it is
connected to the vehicle and uses the protocol throughout the testing till
another vehicle is diagnosed.
√ If the code reader fails to communicate with the vehicle a
“Communication Error!” message displays. Make sure the OBDII
connector is securely attached, and the ignition key is on. Turn vehicle
key to off for 10 seconds, then on. If problem still exists, refer to
“Error Messages” on page 33 of Troubleshooting.
√ When the code reader links to vehicle, it checks the status of I/M
Monitors, and gives a summary report on the display as illustrated below.
√ If vehicle is equipped with more than one computer module (for example
a powertrain control module [PCM] and a transmission control module
[TCM]), the code reader identifies them by their identification names (ID)
assigned by manufacturer (i.e. Engine or A/T).
√ Use the SCROLL key to select a control module where the data may be
retrieved when more than one module is detected.
5. OBDII/EOBD Diagnosis
√ Use the SCROLL key to select a control module where the data may be
retrieved when more than one module is detected.
√ To view information of other control unit quit current test and select
another module.
The Read Codes function is used to read DTCs (stored codes), which are used
to help identify the cause of a trouble or troubles with a vehicle, and pending
codes from the vehicle’s control modules.
√ When emission-related or drivability fault occurs the control module
illuminates the malfunction indicator lamp (MIL).
√ Pending Codes are also referred to as continuous monitor or maturing c
odes that indicate intermittent faults. If the fault does not occur within a
certain number of drive cycles (depending on vehicle), the code clears
from memory. If fault occurs a specific number of times, the code
matures into a DTC and the MIL illuminates or blinks.
√ This function can be performed with KOEO or KOER.
To read codes from vehicle control modules:
1. Press the YES/NO key to start diagnosis from home screen.
2. Use the SCROLL key to select Read Codes from
Diagnostic Menu screen.
5.1 Reading DTCs
18 19
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laser 5089 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laser 5089 in the language / languages: English as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info