729366
107
Zoom out
Zoom in
Previous page
1/122
Next page
LANCOM 1722 VoIP – LANCOM 1723 VoIP – LANCOM 1724 VoIP – LANCOM 1823 VoIP
Chapter 12: Configuring the ISDN and analog interfaces in detail
107
EN
Plug the cable in again and start the device.
A change to the software configuration is also necessary if the ISDN
interfaces are to be set to a different mode. If devices are to be con-
nected to an ISDN interface which is set differently to its default set-
tings, the supplied adapter must be used. This adapter serves to cross-
over the contacts in the ISDN interface.
12.3 Protocol setting
Parameters for the ISDN interfaces are entered into LANconfig in the config-
uration area 'Interfaces' on the 'WAN' tab. Under WEBconfig, Telnet or SSH
client you will find the settings for the ISDN interface parameters under
Setup/Interfaces/WAN
.
Select the protocol for each ISDN interface according to its application and the
ISDN connection type: Point-to-multipoint and point-to-point connections
can be used in various combinations at a LANCOM VoIP Router. The following
options are available:
Automatic for automatic selection of the operating mode (only in TE
mode)
DSS1 TE (Euro ISDN) for connection to a point-to-multipoint ISDN bus.
DSS1 TE point-to-point for connection to a point-to-point ISDN bus.
1TR6 TE (German ISDN) for connection an ISDN bus which uses this pro-
tocol (in Germany only).
DSS1 NT (Euro ISDN) to provide point-to-multipoint ISDN interfaces
DSS1 NT reverse to provide point-to-multipoint interfaces while main-
taining the ISDN timing of the connected ISDN line, please refer to ’ISDN
connection timing’
DSS1 NT (point-to-point) to provide point-to-point ISDN interfaces
DSS1 NT point-to-point reverse to provide point-to-point interfaces
while maintaining the ISDN timing of the connected ISDN line, please
refer to ’ISDN connection timing’
LANCOM 1724
VoIP only
DSS1 timing to adopt the ISDN timing of the connected ISDN line (please
refer to ’ISDN connection timing’), without signaling and other functions
Leased-line GRP0 for Group 0 leased lines over ISDN
Off
107


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lancom 1722 VoIP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lancom 1722 VoIP in the language / languages: English as an attachment in your email.

The manual is 2,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info