812601
7
Zoom out
Zoom in
Previous page
1/36
Next page
MANUAL FOR USE AND MAINTENANCE LSC 001 -UK- REV. 06 7
STARTING UP AND PROGRAMMING THE APPLIANCE
(Range New - Rapid - Spazio - S3 EP/EK - S5 – Compact models)
FOLLOW THE INSTRUCTIONS BELOW (REFERRING TO THE LIST OF PARTS ON PAGES 27/34.
2.1 STARTING UP
FILLING THE BOILER
a) Open the water supply tap as tted during the preparatory stages (2 - Pict.1 - page 6).
b)
Make sure that on the pressure gauge of the motor-driven pump (17) you can read the water mains
pressure ( approx. 4 bar).
c) Push the manual lling valve on the appliance (1) until the boiler level indicator is halfway (2).
In group 1 - Compact models and on models from the Rapid - Spazio range tted with additional steam
wand, to have access to this tap, it is necessary to remove the drip tray (9). The closing of this tap is
manual.
SWITCHING ON THE APPLIANCE
Turn on the main switch (1 - Pict.1 - page 6), as described for the preparation of the system, then turn on
the appliance switch (3) setting it to ON/1 and making sure that the electric connection control light (22),
where present, switches on.
For the S5 range, when the appliance is switched on, the electronic part carries out a check; all symbols on
the control panel are switched on from left to right. At the end of this stage, the symbol for the temperature
setting will start to ash to indicate that the appliance is heating up.
NOTE. According to the amount of water lled manually, it is possible to use the automatic rell
system when the switch (3) is turned on, until the boiler water level indicated by the manufacturer
is reached.
ELECTRIC SWITCHING ON AND BOILER WATER REFILL
In the S5 1 GROUP range, in order to rell the boiler with water , turn on the main switch as arranged
in the preparatory stages ( 1-Pict 1- page 6) ,then open the water supply tap ( 2- Pict 1 page 6 ) making
sure that the water mains pressure is visualized ( approx 4 bar ) on the pressure gauge of the motor-pump
( 17).
Turn the switch knob of the machine to position 1, the LEDS on the touchpad switch on , indicating that
the machine is connected to power , the boiler water rell sets in motion automatically until the boiler water
level indicated by the manufacturer is reached.
ONLY FOR EQUIPMENT FITTED TO OPERATE WITH GAS (optional)
a) Open the gas tap mentioned in the preparation of the system (4 - Pict.1 - page 6).
b) Turn the knob (30) on the machine by 90° until the symbol of the large ame on the knob itself is at the
top.
c) Push the knob (30) and the gas igniter (31) at the same time until the gas turns on; this can be seen
through the inspection opening (41).
d) Hold down the knob (30) for about 10 seconds and check through the special inspection opening (41),
that the ame stays lit.
e) It is recommended to turn the gas adjustment knob (30) to the small ame setting during summer to
prevent useless overheating of the coffee cups on the top grid of the machine (14).
2
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for La Spaziale SPAZIO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of La Spaziale SPAZIO in the language / languages: English as an attachment in your email.

The manual is 1.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info