696218

La Nordica Wanda Classic Evo Manual

24
Zoom out
Zoom in
Previous page
1/96
Next page
ENGLISH
The device is equipped with registers of primary and secondary air.
A- PRIMARY air register (Picture 6)
With the primary air control is adjusted the passage of air through the ash drawer and the grate in the fuel direction. The primary air is
necessary for the combustion process. The ash drawer must be regularly emptied, so that the ash does not obstruct the primary air entry.
Through the primary air the re is also kept alive.
During wood combustion, the register of primary air must be opened only for a while, because otherwise the wood burns fast and the stove
may overheat. For the correct arrangement (see chapter Normal operation).
B - SECONDARY air register (Picture 6)
Over the door of the hearth there is the secondary air control.This regulator must be open (the lever must be moved to the right), especially
for wood combustion, so that un-burnt carbon does not undergo a post-combustion. See chapter Normal operation. Through this register
it is possible to adjust the power of the stove.
Leaving it slightly open, according to the ue of the chimney, it is possible to keep the glass clean.
The adjustment of the registers necessary to reach the rated caloric yield is the following one:
Hourly consumption in kg/h PRIMARY air SECONDARY air TERTIARY AIR
WANDA EVO 2,3 10% Open 75% Open PRE - ADJUSTED
WANDA CLASSIC EVO 2,3 10% Open 75% Open PRE - ADJUSTED
C - AIR REGISTER for the heating of the environment (Picture 6).
This register, through a fan controlled by a thermoregulator pos. D, adjusts the warm air output ONLY from the front side of the appliance.
D - FAN ELECTRIC THERMOCONTROLLER (Picture 6 - Picture 9).
UNIT OPERATION.
This electronic thermocontroller for packaged units manages ventilation air ows. The unit is switched on or o by pressing and holding the
1 button. During operation the display shows the set speed alternating with unit status, led 9.
When the unit is o, the display also remains o. The unit can be controlled MANUALLY or AUTOMATICALLY.
WARNING: the correct operation of the unit is assured only for the proper motor for which it has been manufactured.
Improper use relieves the manufacturer from each responsibility.
MANUAL mode
To access MANUAL mode, press the 2 button; when the 3 light comes on the function
is active. The 4-5 buttons are used to select one of the ve fan speeds, also active
when the ue is cold.
The motor is started in automatic mode by a mechanical thermostat (the display
shows WAIT), which is activated when the temperature is at least 45°C (xed value,
not modiable). The 6 led indicates that the thermostat contact is closed.
AUTOMATIC mode
To access AUTOMATIC mode, press the 2 button; when the 7 light comes on the
function is active. Use the 5 button to set the speed. The 4-5 buttons are used to
select one of the ve fan speeds.
In automatic mode the COMFORT temperature can also be selected. Press the 4
button to access the COMFORT temperature setting and then set the value using
4-5. This setting allows the user to reduce fan noise when the room temperature measured by the probe inside the controller exceeds the
comfort set point; the motor operates one speed lower (this mode has no eect in rst speed) and is signalled by the 8 led.
LANGUAGE menu.
Pressing and holding the 2 button accesses the LANGUAGE menu, where the display language can be changed using the 4-5 buttons (IT,
EN, DE, FR). Pressing the 2 button briey again accesses the DISPLAY menu, where the brightness can be adjusted (between 10 and 150).
Pressing the 2 button briey another time accesses the DEGREES menu, where the temperature display can be set as °C or °F.
BUZZER menu
Pressing the 2 button briey a nal time accesses the buzzer menu, where audible buzzer can be enabled or disabled.
REMOTE CONTROL OPERATION:
The electronic controller for packaged units can be managed by an IR remote control.
• The controller is switched on or o by pressing and holding the 11-12 buttons.
• To switch from MANUAL to AUTOMATIC on the IR remote control press the 13-14 buttons. The LED corresponding
to the operating mode comes on, manual 3 or automatic 7.
• In MANUAL mode only the buttons in the 11-13 group are enabled for selecting one of the ve speeds.
• In AUTOMATIC mode, the buttons in the 12-14 group are enabled for selecting one of the ve speeds, as well
as the buttons in the 11-13 group for changing the COMFORT set point.
The 10 LED comes on whenever a button is pressed on the remote control; if this does not happen, check the
batteries.
11
10
12
13 14
A
A
OK
O1
TM
1 2 3 4
5
6
77
8
12
3 7 89
4 5
6
24
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for La Nordica Wanda Classic Evo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of La Nordica Wanda Classic Evo in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info