WARNING: After the rst ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint)
which disappear after a brief using of the appliance. It must be ensured, in any case, a good ventilation of the environment.
Upon the rst ignition we suggest loading a reduced quantity of fuel and slightly increasing the caloric value of the equipment.
It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.
Never switch on the device when there are combustible gases in the room.
To perform a correct rst lighting of the products treated with paints for high temperature, it is necessary to know the following information:
• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,
refractory material and majolica;
• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures within the
range of 300°C - 500°C are detected;
• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense use or
of absolute standstill when season changes;
• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to complete
the various elastic stresses;
• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet paint. This
paint, although during the manufacture it is backed at 250 °C for some hours, must exceed many times and for a given period of time the
temperature of 350 °C before becoming completely embedded in the metallic surfaces.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1. Make sure that a strong air change is assured in the room where the appliance is installed.
2. During the rst starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual) and
keep the product continuously ON for at least 6-10 hours with the registers less open than the value indicated in the instructions manual.
3. Repeat this operation for at least 4-5 or more times, according to your possibilities.
4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load) and,
if possible, keep the lighting periods long avoiding, at least in this initial phase, short ON/OFF cycles.
5. During the rst starts, no object should be leaned on the appliance and in detail on enameled surfaces. Enameled surfaces must
not be touched during heating.
6. Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with excessive
loads.
To light the re, it is suggested to use small wood pieces together with paper or other traded lighting means.
The openings for air (primary and secondary) must be opened together (you must open the eventual Ignition control, and buttery valve
placed on the pipe of smokes exhaust). When the wood starts burning, you may load other fuels and adjust the air for combustion according
to the instructions on paragraph TECHNICAL DESCRIPTION.
Please always be present during this phase.
Never overload the appliance (see cap. TECHNICAL DESCRIPTION / hourly consumption).Too much fuel and too much air for
combustion can cause overheating and therefore damage the appliance. The warranty does not cover the damages due to
overheating of the equipment.
LOW EMISSION FIRE LIGHTING
Smokeless combustion is a way of lighting a re able to signicantly reduce the emission of harmful substances. The wood burns gradually
from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the ame and
therefore burn almost completely.
Place the logs in the hearth a certain distance apart as shown in the Picture 7. Arrange the largest at the bottom and the smallest at the top,
or vertically in the case of tall narrow combustion chambers. Place the re starter module on top of the pile, arranging the rst logs in the
module at right angles to the pile of wood.
Fire STARTER MODULE. This re starter module replaces a paper or cardboard starter.
Prepare four logs, 20 cm long with a cross section of 3 cm by 3 cm Picture 7. Cross the four logs and place them on top of the pile of wood at
right angles, with the re lighter (wax impregnated wood bre for example) in the middle. The re can be lit with a match. If you want, you can
use thinner pieces of wood. In this case, you will need a larger quantity.
Keep the ue gas exhaust valve and combustion air regulator open.
After lighting the re, leave the combustion air regulator open in the position shown in according to the instructions on paragraph TECHNICAL
DESCRIPTION
FUEL PRIMARY Air SECONDARY AirTERTIARY air
WoodCLOSED 1/2 OPEN PRE-ADJUSTED
IMPORTANT:
• do not add further wood between one complete load and the next;
• do not suocate the re by closing the air intakes;
• regular cleaning by a chimney sweep reduces ne particle emissions.
• These instructions are backed by ENERGIA Legno SVIZZERA www.energia-legno.ch
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for La Nordica Sovrana Easy at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of La Nordica Sovrana Easy in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.
The manual is 6,25 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
