626738
8
Zoom out
Zoom in
Previous page
1/20
Next page
29
2. Press and hold the SET key for about 2 seconds. The temperature digit will start flashing.
Press the + or MIN/MAX key to set the high outdoor temp alarm value. (Keep holding the
key will allow the value to increase faster.)
3. Press the ALARM key to confirm the setting. The digit will stop flashing. Press the SET key
to switch on or off the alarm. (The showing of the icon ((())) means that the alarm is
switched on.)
4. Press the ALARM key once. The Low Outdoor Temperature alarm display will be shown.
5. Press and hold the SET key for about 2 seconds. The temperature digit will start flashing.
Press the + or MIN/MAX key to set the low outdoor temp alarm value. (Keep holding the
key will allow the value to increase faster.)
6. Press the ALARM key to confirm the setting. The digit will stop flashing. Press the SET key
to switch on or off the alarm. (The showing of the icon ((())) means that the alarm is
switched on.)
7. Press the HISTORY key or wait for about 30 seconds and the display will return to normal
display mode automatically.
In case the temperature value meets the condition for high alarm or low alarm, the value will be
blinking, along with the corresponding icon ("HI AL"/ "LO AL").
And the buzzer will ring for 2 minutes. User then may press any key to stop the ring.
User may quit the alarm setting and return to the normal display mode by pressing the HISTORY
key.
HIGH AND LOW OUTDOOR HUMIDITY ALARM SETTING
Note:
The High and Low outdoor humidity alarm can be set On/Off independently according to your
needs.
30
Set the Outdoor humidity alarm value (High or Low alarm value):
1. In the normal display mode, press the ALARM key 4 times. The High Outdoor Humidity
alarm display will be shown.
2. Press and hold the SET key for about 2 seconds. The humidity digit will start flashing.
Press the + or MIN/MAX key to set the high outdoor humidity alarm value.
3. Press the ALARM key to confirm the setting. The digit will stop flashing. Press the SET key
to switch on or off the alarm. (The showing of the icon ((())) means that the alarm is
switched on.)
4. Press the ALARM key once. The Low Outdoor humidity alarm display will be shown.
5. Press and hold the SET key for about 2 seconds. The humidity digit will start flashing.
Press the + or MIN/MAX key to set the low outdoor humidity alarm value.
6. Press the ALARM key to confirm the setting. The digit will stop flashing. Press the SET key
to switch on or off the alarm. (The showing of the icon ((())) means that the alarm is
switched on.)
7. Press the HISTORY key or wait for about 30 seconds and the display will return to normal
display mode automatically.
In case the humidity value meets the condition for high alarm or low alarm, the value will be
blinking, along with the corresponding icon ("HI AL"/ "LO AL"). And the buzzer will ring for 2
minutes. User may press any key to stop the sound.
31
WIND SPEED ALARM SETTING
The High wind speed alarm can be set by following the steps below.
1. In the normal display mode, press the ALARM key six times. The High wind-speed alarm
display will be shown.
2. Press and hold the SET key for about 2 seconds. The wind speed digit will start flashing.
Press the + or MIN/MAX key to set the high wind speed alarm value.
3. Press the ALARM key to confirm the setting. The digit will stop flashing. Press the SET key
to switch on or off the alarm. (The showing of the icon ((())) means that the alarm is
switched on.)
4. Press the ALARM key once to return to the normal display mode.
In case the wind speed exceeds the condition for high wind speed alarm, the value will be
flashing, along with the corresponding high alarm icon ("HI AL"). And the buzzer will ring for 2
minutes. User may press any key to stop the sound.
HYSTERESIS
To compensate for fluctuation of the measured data, which may cause the weather alarm to
sound constantly if the measured reading is close to your set level, a hysteresis function has
been implemented for each weather alarm. For example, if the high temperature alarm is set to
+77°F and the current value moves to +77°F, the alarm will be activated (if it has been enabled).
Now when the temperature drops to +76.8°F or below and thereafter again increases to beyond
+77°F, the data will be blinking, but no alarm will be activated. It has to drop to below +75.2°F
32
(with a pre-set hysteresis of 1.8°F) so that the alarm can be produced again. Hysteresis values
for the various weather data types are given in the following table:
Weather data Hysteresis
Temperature 1.8°F
Humidit
y
3% RH
Wind speed 3.1 mph
Note:
The temperature, humidity or wind data will keep on flashing even after a key has been pressed
to stop the alarm or buzzer has been switched off, to indicate that the current weather condition
is out of the pre-set limit(s)
WEATHER FORECAST AND WEATHER TENDENCY
WEATHER FORECASTING ICONS:
Weather forecasting icons are displayed in any of the following combinations at the right bottom
part of LCD:
For every sudden or significant change in the air pressure, the weather icons will update
accordingly to represent the change in weather.
Sunny
TENDENCY
Cloudy with sunny
intervals
TENDENCY
Rainy
TENDENCY
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for La Crosse WS-1516-IT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of La Crosse WS-1516-IT in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info