Manual La Crosse WS- 1912 (page 4 of 20) (English)

626740

Zoom out

Zoom in

1/20

2. Next, insert the batteries into the Thermo-hygro sensor and Rain sensor (optional -

purchased separately) See “How to install and replace the batteries into the

Thermo-hygro sensor“ and “How to install and replace the batteries into the

Rain sensor (optional)” below.

3. Then insert the batteries into the Weather Center (See “How to install and replace

the batteries into the Weather Center” below). Once the batteries are installed, all

segments of the LCD will light up briefly. It will then display the time as 12:00, the

date as 1.1.09, the weather icons, and air pressure value. "- - -" will be shown for

outdoor data.

4. Afterwards, the Weather Center will start receiving data from the transmitter. The

transmission reception icon will be blinking to indicate that the station is trying to get

the thermo-hygro transmitter data. The outdoor temperature, humidity, wind data

should then be displayed on the Weather Center. If this does not happen after 135

seconds, the batteries will need to be removed from all units. You will have to start

again from step 2.

5. The transmitter reception icon is now blinking again to indicate that the station is

trying to get the rain sensor data. It will stop blinking once the rain sensor has been

detected. If this does not happen after 135 seconds, you will need to start again from

step 2.

6. You should check the cable for correct connections and test all the components for

correct functionality by manually turning the wind-gauge and by moving the wind-

vane; tilting the optional rain sensor to hear the impact of the internal moving seesaw,

etc. (See Positioning below).

7. Time and date must be manually set (See Manual Setting below).

8. After the Weather Center has been tested with regard to the above points and found

fit, the initial set up of the weather station system is finished and the mounting of the

system components can take place. It must be ensured however that all components

work properly together at their chosen mounting or standing locations.

For example, if there appears to be problems with the 915 MHz radio transmission,

they can mostly be overcome by slightly changing the mounting locations or turning

the base station.

Note:

The radio communication between the receiver and the transmitters in the open field

reaches distances of up to 330 feet/ 100 meters, provided there are no interfering

obstacles such as buildings, trees, vehicles, high voltage lines, etc.

9. Radio interferences created by cordless phones, PC screens, radios or TV sets can

in some cases entirely cut off radio communication. Please consider this when

choosing standing or mounting locations.

Note :

 After batteries are installed in the transmitter, install the batteries in the weather

center to receive the signal from the transmitters as soon as possible. If the weather

center is powered more than 5 hours after the transmitter is powered, the weather

center will never receive signal successfully from the transmitters. In this case, you

will need to reinstall the batteries from all the transmitters to redo set-up procedure.

 After batteries are installed, there will be synchronization between Weather Center

and the transmitters. At this time, the signal reception icon

will be blinking. When

the signal is successfully received by the Weather Center, the

icon will be

switched on (If it is not successful, the

icon will not be shown).

 The short blinking of the icon shows that a reception is in progress.

 If the signal reception is not successful on the first frequency (915MHz) for 45

seconds, the frequency is changed to 920MHz and the learning is tried another 45

seconds. If still not successful, the reception is tried for 45 seconds on 910MHz. This

will also be done for re-synchronization.

Transmitter signal

reception icon

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of La Crosse WS- 1912 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

La Crosse WS- 1912 Manual

Product: