17444
18
Zoom out
Zoom in
Previous page
1/54
Next page
CHAPTER 3 PREPARATIONS BEFORE USE
2. How to set originals
(1) Setting originals into the DF
Precautions for the use of DF
Do not use any of the originals given below with the DF. Also do not
set originals with punch holes or tear-off strips positioned as the
leading edge.
• Transparency films
• Carbon paper and extremely creased or folded originals, originals of
soft material such as vinyl
• Non-square originals, wet originals, originals with adhesive tape or
glue
• Originals bundled with a paper clip or staple (if inevitable, remove
the paper clip or staple and straighten out the creases and folds
before setting the originals)
• Clipped out originals, originals with slippery surfaces
• Originals with still-wet whiteout
• Originals with creases (if inevitable, straighten out the creases
before setting the originals)
18 ppm copier
The DF automatically feeds multiple sheet originals one by one for
scanning.
Originals that can be used with the DF
(Inch specifications)
Sheet originals only
Original weights: Single-sided original of 50 to 120 g/m
2
Original sizes: 8 1/2" x 11", 5 1/2" x 8 1/2" (vertical), 8 1/2" x 14"
Capacity:
Up to 30 sheets of standard paper of 50 to 80 g/m
2
As many sheets of standard paper of 80 to 120 g/m
2
(excluding
80 g/m
2
) as can be loaded up to the limit indicated on the sticker
attached on the rear original insertion guide
1 sheet of special paper (art paper, thermal paper)
(Metric specifications)
Sheet originals only
Original weights: Single-sided original of 50 to 120 g/m
2
Original sizes: A4, A5 (vertical), folio
Capacity:
Up to 30 sheets of standard paper of 50 to 80 g/m
2
As many sheets of standard paper of 80 to 120 g/m
2
(excluding
80 g/m
2
) as can be loaded up to the limit indicated on the sticker
attached on the rear original insertion guide
1 sheet of special paper (art paper, thermal paper)
Setting originals
1
Adjust the original insertion guides to the original size.
* Before setting the originals in the DF, check that no original
from the previous operation remains on the original eject
cover. Originals remaining on the original eject cover may
cause an original misfeed.
2
Set the originals on the original table in correct sequence
with the side to be copied facing upward. Securely insert the
leading edge of the originals into the DF as far as they will
go.
IMPORTANT
Do not set originals exceeding the limit indicated on the sticker
attached on the rear original insertion guide. Setting more originals
than specified may cause an original misfeed.
3-5
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera KM1510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera KM1510 in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info