435980
74
Zoom out
Zoom in
Previous page
1/76
Next page
Please read the Operation Guide before using the copier
Keep it close to the copier for easy reference
KM-
1500
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying, recording or by any information storage and
retrieval system, without permission in writing from the Publisher.
Legal Restriction On Copying
It may be prohibited to copy copyrighted material without permission of the copyright owner.
It is prohibited under any circumstances to copy domestic or foreign currencies.
Copying other items may be prohibited.
i
The explanations contained in this operation guide have been
separated into different sections in order to allow even those using
a copier for the first time to use this machine efficiently, properly
and with relative ease.
A basic introduction to each section can be found below for
reference. Refer to the related section when using this copier.
Section 1 IMPORTANT! PLEASE READ FIRST.
This section contains explanations on information that is necessary
for you to know prior to using this copier for the first time after
purchase.
For example, it contains notes and cautions on installation and
operation that should be strictly obeyed in order to ensure its safe
and proper operation.
Section 2 NAMES OF PARTS
This section contains explanations on the names and functions of
the parts of the copier and its operation panel.
Section 3 PREPARATIONS
This section contains explanations on loading copy paper and
attaching the face-up tray.
Section 4 BASIC OPERATION
This section contains explanations on the basic procedures
required to make simple copies.
Section 5 COPY FUNCTIONS
This section contains explanations on using the various convenient
functions of this copier.
Section 6 COPY DEFAULT SETTINGS
This section contains explanations on changing the various default
settings available for adjusting the copier to fit your copy needs.
Section 7 TROUBLESHOOTING
This section contains explanations on handling problems that may
occur during operation of this copier, such as when an error
indication appears or if a paper jam occurs.
Section 8 MAINTENANCE AND OPERATION
INFORMATION
This section contains explanations on maintaining the copier in
proper condition and on replacing the toner container, as well as
information on the specifications for this copier.
This Operation Guide contains certain symbols to indicate points of
caution and additional information that is important for you to
know.
The symbols and their meanings are indicated below.
IMPORTANT!
This symbol indicates information on procedures that should or
should not be performed in order to avoid trouble.
NOTE(S)
This symbol indicates information on additional explanations or
procedures for your reference.
Introduction to this Operation Guide Symbols in this guide
ii
CONTENTS
Energy Star Program ...................................................................... iii
Please read this Operation Guide before using the copier. Keep it
close to the copier for easy reference. ..............................................iv
Section 1
IMPORTANT! PLEASE READ FIRST. 1-1
CAUTION LABELS .......................................................................1-1
INSTALLATION PRECAUTIONS ................................................1-2
PRECAUTIONS FOR USE ............................................................1-3
Section 2
NAMES OF PARTS ..................................2-1
Main Body .......................................................................................2-1
Operation panel ..............................................................................2-4
Section 3
PREPARATIONS .....................................3-1
Loading paper .................................................................................3-1
Note when adding paper ..........................................................3-1
Loading paper into a drawer ...................................................3-1
Setting paper on the multi-bypass tray ..................................3-5
Thick Paper mode ....................................................................3-9
Attaching the face-up tray ...........................................................3-10
Section 4
BASIC OPERATION ................................4-1
Basic copying procedure .................................................................4-1
Making enlarged and reduced copies ............................................4-4
Zoom mode ................................................................................4-4
Preset Zoom mode ....................................................................4-5
Section 5
COPY FUNCTIONS .................................5-1
Layout modes .................................................................................5-1
2-in-1 .........................................................................................5-1
4-in-1 .........................................................................................5-5
Selecting the borderline ...........................................................5-6
Selecting the order of 4-in-1 layout .........................................5-7
Sort mode ........................................................................................5-9
Section 6
COPY DEFAULT SETTINGS .................6-1
Available default items ..................................................................6-1
Accessing and changing the default settings ................................6-4
Checking the total copy count and printing out a report ...........6-10
Section 7
TROUBLESHOOTING ............................ 7-1
If one of the following indications is displayed ............................7-1
If paper jams ..................................................................................7-3
Misfeed location indicators .....................................................7-3
Cautions ...................................................................................7-3
Removal procedures ................................................................7-4
If other trouble occurs ....................................................................7-9
Section 8
MAINTENANCE AND OPERATION
INFORMATION ....................................... 8-1
Cleaning the copier ........................................................................8-1
Replacing the toner container .......................................................8-2
Specifications ................................................................................. 8-6
Main Body ................................................................................8-6
Document Processor (option) ..................................................8-7
Paper Feeder (option) ..............................................................8-7
Additional Memory (option) ....................................................8-7
Environmental Specifications .......................................................8-8
iii
Energy Star Program
We have determined as a participating company in the
International Energy Star Program that this product is compliant
with the standards laid out in the International Energy Star
Program.
International Energy Star Program has as its basic goals the
promotion of efficient energy use and the reduction of the
environmental pollution that accompanies energy consumption by
promoting the manufacture and sale of products that fulfill
program standards.
International Energy Star Program standards require that copies
come equipped with a “Low Power Mode” where energy
consumption is reduced after a certain amount of time elapses
since the device was last used, as well as an “Off Mode” where the
device automatically turns itself off after there is no activity within
a set amount of time. When the copier includes printer and fax
functions, the printer and fax must enter a “Low Power Mode”
where power consumption is automatically reduced after a certain
amount of time elapses since they were last used, and they must
also support a “Sleep Mode” where power consumption is reduced
to a minimum when there is no activity within a set amount of
time.
This product is equipped with the following features as a result of
its compliance with International Energy Star Program standards.
Low Power Mode
The device automatically enters “Low Power Mode” when 15
minutes have passed since the device was last used. The amount of
time of no activity that must pass before “Low Power Mode” is
activated may be lengthened.
Off Mode
The device automatically enters “Off Mode” when 60 minutes have
passed since the device was last used. The amount of time of no
activity that must pass before “Off Mode” is activated may be
lengthened.
Paper Recycling
The Energy Star Program encourages the use of environmentally
friendly recycled paper. Your sales or service representative can
provide information about recommended paper types.
About the International Energy Star Program
iv
Please read this Operation Guide before using the copier. Keep it close to the copier for easy reference.
Please read this Operation Guide before using the copier. Keep it close to the copier for easy
reference.
The sections of this guide and parts of the copier marked with symbols are safety warnings meant to
protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the
copier. The symbols and their meanings are indicated below.
Symbols
The symbol indicates that the related section includes safety warnings. Specific points of attention are
indicated inside the symbol.
The symbol indicates that the related section includes information on prohibited actions. Specifics of
the prohibited action are indicated inside the symbol.
The z symbol indicates that the related section includes information on actions which must be
performed. Specifics of the required action are indicated inside the symbol.
Please contact your service representative to order a replacement if the safety warnings in this Operation
Guide are illegible or if the guide itself is missing. (fee required)
DANGER: Indicates that serious injury or even death will very possibly result from
insufficient attention to or incorrect compliance with the related points.
WARNING: Indicates that serious injury or even death may result from insufficient
attention to or incorrect compliance with the related points.
CAUTION: Indicates that personal injury or mechanical damage may result from
insufficient attention to or incorrect compliance with the related points.
..........[General warning]
..........[Warning of danger of electrical shock]
..........[Warning of high temperature]
..........[Warning of prohibited action]
..........[Disassembly prohibited]
..........[Alert of required action]
..........[Remove the power plug from the outlet]
..........[Always connect the copier to an outlet with a ground connection]
1-1
Section 1 IMPORTANT! PLEASE READ
FIRST.
CAUTION LABELS
Caution labels have been attached to the copier at the following locations for safety purposes.
BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing
toner.
Label 1
High temperature inside.
Do not touch parts in this area,
because there is a danger of getting
burned. ..............................................
NOTE: DO NOT remove these labels.
Label 2
High temperature inside.
Do not touch parts in this area,
because there is a danger of getting
burned. ..............................................
1-2
INSTALLATION PRECAUTIONS
Environment
CAUTION
Avoid placing the copier on or in locations
which are unstable or not level. Such
locations may cause the copier to fall down or
fall over. This type of situation presents a
danger of personal injury or damage to the
copier.
.............................................................................
Avoid locations with humidity or dust and
dirt. If dust or dirt become attached to the
power plug, clean the plug to avoid the
danger of fire or electrical shock.
.......................
Avoid locations near radiators, heaters, or
other heat sources, or locations near
flammable items, to avoid the danger of fire.
To keep the copier cool and facilitate
changing of parts and maintenance, allow
access space as shown below. Leave adequate
space, especially around the vents, to allow
air to be properly ventilated out of the copier.
Other precautions
Adverse environmental conditions may affect the safe
operation and performance of the copier. Install in an
air-conditioned room (recommended room
temperature: around 68°F (20°C), humidity: around
65%) and avoid the following locations when selecting
a site for the copier.
Avoid locations near a window or with exposure to
direct sunlight.
Avoid locations with vibrations.
Avoid locations with drastic temperature
fluctuations.
Avoid locations with direct exposure to hot or cold
air.
Avoid poorly ventilated locations.
During copying, some ozone is released, but the
amount does not cause any ill effect to one's health. If,
however, the copier is used over a long period of time
in a poorly ventilated room or when making an
extremely large number of copies, the smell may
become unpleasant. To maintain the appropriate
environment for copy work, it is suggested that the
room be properly ventilated.
Power supply/Grounding the copier
WARNING
DO NOT use a power supply with a voltage
other than that specified. Avoid multiple
connections in the same outlet. These types
of situations present a danger of fire or
electrical shock.
.........................................................
Plug the power cord securely into the outlet.
If metallic objects come in contact with the
prongs on the plug, it may cause a fire or
electric shock.
.............................................................
Always connect the copier to an outlet with a
ground connection to avoid the danger of fire
or electrical shock in case of an electric short.
If an earth connection is not possible, contact
your service representative.
................................
Other precautions
Connect the power plug to the closest outlet possible
to the copier.
The power supply cord is used as the main disconnect
device. Ensure that the socket/outlet is
located/installed near the equipment and is easily
accessible.
Handling of plastic bags
WARNING
Keep the plastic bags that are used with the
copier away from children. The plastic may
cling to their nose and mouth causing
suffocation.
..................................................................
Left:
11
13/16"
30 cm
Front:
39
3/8"
100 cm
Right:
11
13/16"
30 cm
Rear:
11
13/16"
30 cm
1-3
PRECAUTIONS FOR USE
Cautions when using the copier
WARNING
DO NOT place metallic objects or containers
with water (flower vases, flower pots, cups,
etc.) on or near the copier. This of situation
presents a danger of fire or electrical shock
should they fall inside. ..................................
DO NOT remove any of the covers from the
copier as there is a danger of electrical shock
from high voltage parts inside the copier. ....
DO NOT damage, break or attempt to repair
the power cord. DO NOT place heavy objects
on the cord, pull it, bend it unnecessarily or
cause any other type of damage.
These types of situations present a danger of
fire or electrical shock. ...................................
NEVER attempt to repair or disassemble the
copier or its parts as there is a danger of fire,
electrical shock or damage to the laser. If the
laser beam escapes, there is a danger of it
causing blindness............................................
If the copier becomes excessively hot, smoke
appears from the copier, there is an odd
smell, or any other abnormal situation
occurs, there is a danger of fire or electrical
shock. Turn the power switch OFF ({)
immediately, BE ABSOLUTELY CERTAIN
to remove the power plug from the outlet and
then contact your service representative. .....
If anything harmful (paper clips, water,
other fluids, etc.) falls into the copier, turn
the power switch OFF ({) immediately.
Next, BE ABSOLUTELY CERTAIN to
remove the power plug from the outlet to
avoid the danger of fire or electrical shock.
Then contact your service representative. ...
DO NOT remove or connect the power plug
with wet hands, as there is a danger of
electrical shock. ..............................................
ALWAYS contact your service representative
for maintenance or repair of internal parts.
CAUTION
DO NOT pull the power cord when removing
it from the outlet. If the power cord is pulled,
the wires may become broken and there is a
danger of fire or electrical shock. (ALWAYS
grasp the power plug when removing the
power cord from the outlet.) .........................
ALWAYS remove the power plug from the
outlet when moving the copier. If the power
cord is damaged, there is a danger of fire or
electrical shock. .............................................
If the copier will not be used for a short
period of time (overnight, etc.), turn the
power switch OFF ({).
If it will not be used for an extended period of
time (vacations, etc.), remove the power plug
from the outlet for safety purposes during
the time the copier is not in use. ..................
ALWAYS hold the designated parts only
when lifting or moving the copier. ................
For safety purposes, ALWAYS remove the
power plug from the outlet when performing
cleaning operations. .......................................
If dust accumulates within the copier, there
is a danger of fire or other trouble. It is
therefore recommended that you consult
with your service representative in regard to
cleaning of internal parts. This is
particularly effective if accomplished prior to
seasons of high humidity. Consult with your
service representative in regard to the cost of
cleaning the internal parts of the copier. .....
1-4
Other precautions
DO NOT place heavy objects on the copier or cause
other damage to the copier.
DO NOT open the upper front cover, turn off the
power switch, or pull out the power plug during
copying.
When lifting or moving the copier, contact your
service representative.
Do not touch electrical parts, such as connectors or
printed circuit boards. They could be damaged by
static electricity.
DO NOT attempt to perform any operations not
explained in this handbook.
CAUTION: Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Do not look directly at the light from the scanning
lamp as it may cause your eyes to feel tired or painful.
Cautions when handling
consumables
CAUTION
DO NOT attempt to incinerate the toner
container. Dangerous sparks may cause
burns. .............................................................
Keep the toner container out of the reach of
children. .........................................................
If toner happens to spill from the toner
container, avoid inhalation and ingestion, as
well as contact with your eyes and skin. ......
If you do happen to inhale toner, move to a place
with fresh air and gargle thoroughly with a large
amount of water. If coughing develops, contact a
physician.
If you do happen to ingest toner, rinse your mouth
out with water and drink 1 or 2 cups of water to
dilute the contents of your stomach. If necessary,
contact a physician.
If you do happen to get toner in your eyes, flush
them thoroughly with water. If there is any
remaining tenderness, contact a physician.
If toner does happen to get on your skin, wash with
soap and water.
DO NOT attempt to force open or destroy the
toner container. .............................................
Other precautions
After use, ALWAYS dispose of the toner container in
accordance with Federal, State and Local rules and
regulations.
Store all consumables in a cool, dark location.
If the copier will not be used for an extended period of
time, remove the paper from the drawer, return it to
its original package and reseal it.
1-5
Laser Safety
Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside
this machine is hermetically sealed within the protective housing and external cover. In the normal
operation of the product by user, no radiation can leak from the machine.
This machine is classified as Class 1 laser product under IEC 60825.
CAUTION
Performance of procedures other than those specified in this manual may result in hazardous radiation
exposure.
This label is attached to the laser scanner unit inside the machine and is not in a user access area.
The labels shown below are attached on the rear side of the machine.
1-6
CAUTION!
The power plug is the main isolation device! Other switches on the equipment are only functional
switches and are not suitable for isolating the equipment from the power source.
VORSICHT!
Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem Gerät sind nur
Funktionsschalter und können nicht verwendet werden, um den Stromfluß im Gerät zu unterbrechen.
1-7
DECLARATION OF CONFORMITY
TO
89/336/EEC, 73/23/EEC and 93/68/EEC
We declare under our sole responsibility that the product to which
this declaration relates is in conformity with the following specifications.
Limits and methods of measurement for immunity
characteristics of information technology equipment EN55024
Limits and methods of measurement for radio interference
characteristics of information technology equipment EN55022 Class B
Limits for harmonic currents emissions
for equipment input current 16A per phase EN61000-3-2
Limitation of voltage fluctuations and flicker in low-voltage
supply systems for equipment with rated current 16A EN61000-3-3
Safety of information technology equipment,
including electrical equipment EN60950
Radiation Safety of laser products, equipment classification,
requirements and user’s guide EN60825-1
1-8
2-1
Section 2 NAMES OF PARTS
(1) Original cover
(Open/close this cover when you are setting the original on the
platen.)
(2) Platen
(Set originals here for copying. Be sure to lay originals
face-down and align them flush up against the left rear corner
of the platen.)
(3) Original size indicator plate
(Be sure to align originals flush up against this plate when
setting them on the platen.)
(4) Operation panel
(Perform copy operations here.)
(5) Upper front cover
(Open this cover when you need to replace the toner container
or if a paper jam occurs inside the copier.)
(6) Front cover
(Open this cover when you need to replace the toner container
or if a paper jam occurs inside the copier.)
(7) Process Unit
(Take this unit out when you need to replace the toner
container or if a paper jam occurs inside the copier.)
(8) Toner container
(9) Lock lever
(Operate this lever when you need to replace the toner
container.)
(10) Toner container release lever
(Operate this lever when you need to replace the toner
container.)
(11) Charger cleaner
(Slide this knob back and forth when you need to clean the
charger.)
Main Body
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) (10)(9)
(11)
Section 2 NAMES OF PARTS
2-2
(12) Drawer
(This drawer has a storage capacity of 250 sheets of standard
copy paper (80 g/m²).)
(13) Paper width guides
(Adjust these guides to fit the width of the paper that is to be
loaded in the drawer.)
(14) Paper stopper
(Adjust this stopper to fit the length of the paper that is to be
loaded in the drawer.)
(15) Stopper extension lock
(Use this lock when loading Folio or Oficio II size paper in the
drawer.)
(16) Copy storage table
(Finished copies can be ejected and stored on this table. The
copy storage table has a storage capacity of 150 sheets of
standard copy paper (80 g/m²).)
(17) Multi-bypass tray
(Set paper on this tray when copying onto small-size or special
paper.)
(18) Multi-bypass extension
(Pull out this extension when using the multi-bypass tray.)
(19) Insert guides
(Align these guides to fit the width of the paper that is to be
set on the multi-bypass tray.)
(12)
(13)
(14)
(15)
(16)
(13)
(17) (18)
(19) (19)
Section 2 NAMES OF PARTS
2-3
(20) Power switch
(Turn this switch ON ( | ) before copying.)
(21) Face-up tray
(Finished copies can be ejected and stored face-up on this tray.
The face-up tray should be used when copying onto thick
paper and other special paper. This tray has a storage
capacity of 30 sheets of standard copy paper (80 g/m²) but only
1 sheet of special paper should be stored there at one time.)
(22) Power cord
(23) Document Processor connector
(Attach the connection cable here when installing the optional
Document Processor.)
(24) Right cover anchor pin
(This pin must be removed and the right cover opened in order
to access the slot for installing additional memory. If you need
to add additional memory, contact your service representative
or an authorized service center.)
(20)
(21)
(22)
(23)
(24)
IMPORTANT!
Be sure to hold both the front and rear sides of the copier when carrying it, as shown in the illustration.
Be sure not to pull the drawer out when holding the front of the copier.
Be sure that the original cover is closed whenever transporting the copier.
DO NOT attempt to carry the copier by holding only the top portion. Doing so may result in you dropping the copier and thereby
damaging the copier and/or its covers.
Section 2 NAMES OF PARTS
2-4
(1) Start key & indicator
(Press this key when you want to start copying. Copying will
begin immediately if you press this key when the indicator is
lit green.)
(2) Reset/Power key
(Press this key when you want to cancel the currently entered
setting(s) and return to those registered for the initial mode.
Press down on this key for at least 3 seconds when you want to
engage the Off mode. When you want to release the copier
from the Off mode, press any one of the keys on the operation
panel. See page 2-5.)
(3) Stop/Clear key
(Press this key when you want to stop copying. Press down on
this key for at least 3 seconds when you want to view the total
copy count. See page 6-10.)
(4) Copy quantity/magnification display
(Displays the number of copies to be made or the currently
selected magnification ratio. When the “%” symbol is lit, the
displayed number is the currently selected magnification
ratio.)
(5) Exposure adjustment keys
(Press the left key when you want to make the copy exposure
lighter and the right key to make the exposure darker. Press
down on both keys at the same time for at least 3 seconds
when you want to access the default settings mode.)
(6) Image quality select key
(Press this key when you want to select the desired image
quality mode. See page 4-1.)
(7) Number of Copies / Zoom(+) key
(Press this key when you want to raise the number of copies to
be made, as well as to increase the currently selected copy
magnification ratio. Press this key as well during default
settings in order to select the desired default item or setting.)
(8) Number of Copies / Zoom(-) key
(Press this key when you want to lower the number of copies
to be made, as well as to decrease the currently selected copy
magnification ratio. Press this key as well during default
settings in order to select the desired default item or setting.)
(9) Recall%/Enter key
(Press this key when you want copy in the Zoom mode. Press
this key as well during default settings in order to select the
current default item or register the currently displayed
setting. See page 4-4.)
(10) Reduce/Enlarge key
(Press this key when you want to use the Preset Zoom mode.
See page 4-5.)
(11) Paper Select key
(Press this key when you want to switch paper feed between
the drawer(s) and the multi-bypass tray. The indicator for the
currently selected source of paper feed will be lit green. Press
down on this key for at least 3 seconds when you want to
access the default items for paper size selection. See page 4-1.)
(12) Thick Paper key & indicator
(Press this key when you want to copy onto thick paper. Make
sure that the Thick Paper indicator is lit green. See page 3-9.)
(13) 2in1/4in1 key & indicators
(Press this key when you want to copy with the Layout modes.
Make sure that the 2in1 or the 4in1 indicator, as appropriate,
is lit green. Press down on this key for at least 3 seconds when
you want to access the default items for the Layout modes. See
page 5-1 for more information on the Layout modes.)
(14) Sort key & indicator
(Press this key when you want to copy with the Sort mode.
Make sure that the Sort indicator is lit green. See page 5-9.)
Operation panel
(1)
(2)
(3)
(14)
(15)
(10)(7)(9)(8)(11)(5)(6)
(13)
(16)
(4)(17)(12)
(24)
(23)
(19)
(21)
(22)
(18)
(20)
Section 2 NAMES OF PARTS
2-5
(15) Program key & indicator
(Press this key when you want to copy with the Program
function. Make sure that the Program indicator is lit green.)
(16) Add Toner indicator
(This indicator lights red when the toner supply has run low.
See page 8-2.)
(17) Memory Overflow indicator
(This indicator lights red if the memory becomes full during
scanning of originals. See page 7-1.)
(18) Upper drawer indicator
(This indicator lights green when the upper drawer is selected
as the source of paper feed and it flashes green when the
drawer has run out of paper.)
(19) Upper drawer misfeed indicator
(This indicator lights red if a paper jam occurs in the upper
drawer.)
(20) Paper Feeder indicator
(This indicator lights green when the optional Paper Feeder is
selected as the source of paper feed and it flashes green when
the drawer has run out of paper.)
(21) Paper Feeder misfeed indicator
(This indicator lights red if a paper jam occurs in the optional
Paper Feeder.)
(22) Multi-bypass tray indicator
(This indicator lights green when the multi-bypass tray is
selected as the source of paper feed and it flashes green when
the tray has run out of paper.)
(23) Multi-bypass tray misfeed indicator
(This indicator lights red if a paper jam occurs in the
multi-bypass tray.)
(24) Document Processor indicator
(This indicator will light red if an original jam occurs.)
Initial mode (the state that the copier enters at the end of
warm-up or when the Reset/Power key is pressed)
The upper drawer is selected as the source for paper feed, the
number of copies to be made is set to “1” and “Text & Photo” is
selected as the image quality mode.
* If the optional Paper Feeder is installed on your copier, it is
possible for you to change which drawer will be automatically
selected in the initial mode.
* It is also possible for you to change which image quality mode
will be automatically selected in the initial mode.
Auto Clear function
A pre-set number of seconds (between 10 and 270) after copying
stops, the Auto Clear function will automatically engage and the
copier will return to the same settings as those after warm up
(initial mode settings).(However, the copy exposure setting will not
change.) Copies can continually be made using the same settings
(copy mode and number of copies) if the next batch of copying is
started before the Auto Clear function engages.
Auto Drawer Switching function
If two drawers contain the same size of paper and the paper in one
drawer runs out during copying, the Auto Drawer Switching
function will switch paper feed from the empty drawer to the other
drawer that still contains paper so that copying can continue
non-stop.
* The optional Paper Feeder is required in order to use the Auto
Drawer Switching function.
* It is possible for you to turn the Auto Drawer Switching function
OFF.
Section 2 NAMES OF PARTS
2-6
3-1
Section 3 PREPARATIONS
Copy paper can either be loaded into the drawer(s) or set on the
multi-bypass tray.
Note when adding paper
After taking new paper out of its packaging, be sure to fan through
them a few times to separate the sheets before loading the paper
into a drawer or setting it on the multi-bypass tray.
IMPORTANT!
If you ever use paper that has already been copied
onto, be sure NOT to use paper that still has staples or
clips attached to it. Doing so may result in lowered
copying quality or even damage to the copier.
If you are using paper that has been folded or is curled
at all, straighten it out before loading the paper into a
drawer or setting it on the multi-bypass tray. Failure
to do so may result in a paper jam.
Loading paper into a drawer
Standard copy paper (60 g/m² – 90 g/m²), thick paper (90 g/m² –
105 g/m²), recycled paper, or color paper can be loaded into each
drawer.
Up to 250 sheets of standard copy paper (80 g/m²) can be loaded
into each drawer at one time.
The sizes of paper that can be loaded into the drawers are: A4,
A5R, Folio, 8
1/2" × 14" (Legal), 8 1/2" × 11" (Letter) and 8 1/2" × 13"
(Oficio II).
IMPORTANT!
When loading copy paper for the first time, or when
changing paper sizes, be sure to use the operation
panel to register the size of paper that will be loaded in
the corresponding drawer. (See page 3-4.)
When using thick copy paper (90 g/m² – 105 g/m²), be
sure to select the Thick Paper mode. (See page 3-9.)
Loading paper
Section 3 PREPARATIONS
3-2
1 Pull the drawer all the way out of the copier.
IMPORTANT!
When pulling the drawer out of the copier, be sure to
support it so that it doesn’t fall out suddenly.
2 Adjust the paper stopper in the rear portion of the drawer
by pressing in on the release buttons and sliding the paper
stopper to the fit the size of the paper being loaded.
NOTES
The paper sizes are marked on the bottom of the
drawer.
The factory default setting is for A4/Letter size paper.
For information on adjusting the paper stopper for
Folio or Oficio II size paper, see “Adjusting the
paper stopper for Folio or Oficio II size paper” on
page 3-3.
3 Adjust the paper width guides on both sides of the drawer
by pressing in on the release buttons and sliding the guides
to fit the width of the paper being loaded in the drawer.
NOTES
The paper sizes are marked on the bottom of the
drawer.
The factory default setting is for A4/Letter size paper.
4 Set the paper in the drawer so that the leading edge is
aligned against the paper stopper, but making sure that
none of the paper gets caught on the overhanging tabs.
IMPORTANT!
ALWAYS adjust the paper stopper and paper width
guides BEFORE loading paper into the drawer.
Failure to do so may result in skewed paper feed
and/or a paper jam.
Make sure that the paper is set securely against the
paper stopper and the paper width guides. If there is
any gap between the paper and the stopper or guides,
readjust the paper stopper and/or the paper width
guides, as appropriate.
When you are loading paper into the drawer, make
sure that the side to be copied onto is facing downward.
Be sure to load paper so that it is not folded or curled,
etc.
DO NOT load more paper than indicated by the lines
located on the width guides.
Section 3 PREPARATIONS
3-3
5 Push the drawer securely all the way back into the copier
until it stops.
IMPORTANT!
If you will not be using the copier for a prolonged period
of time, remove all paper from the drawer(s) and seal in
its original packaging in order to protect it against
moisture.
Adjusting the paper stopper for Folio or
Oficio II size paper
Perform the following procedure to adjust the paper stopper when
you want to load Folio or Oficio II size paper into the drawer.
1 Remove the stopper extension lock from the paper stopper.
2 Slide the paper stopper towards the rear of the drawer until
the grooves (1) that are cut into the paper stopper are
aligned with the rear edge of the drawer.
3 Insert the stopper extension lock into the holes in the paper
stopper.
(1)
Section 3 PREPARATIONS
3-4
4 Press down on the stopper extension lock and slide the
paper stopper towards the rear of the drawer to set the lock
into place. The paper stopper is now in position for Folio
and Oficio II size paper.
Selecting the paper size
Perform the following procedure to use the operation panel and
select the size of paper that is loaded in the drawer.
1 Press down on the Paper Select key for at least 3 seconds.
The first default item for paper size selection will be shown.
2 Press the Number of Copies / Zoom(+) or Number of
Copies / Zoom(-) key until “F12” (Default item: Upper
Drawer Paper Size) is shown.
NOTE
To select the size of paper loaded into the optional Paper
Feeder, make sure that “F13” (Default item: Paper
Feeder Paper Size) is shown.
3 Press the Recall%/Enter key.
Section 3 PREPARATIONS
3-5
4 Press the Number of Copies / Zoom(+) or Number of
Copies / Zoom(-) key to select the appropriate paper size.
The displayed code numbers refer to the available paper
sizes as explained in the following table.
5 Press the Recall%/Enter key.
The displayed numbers will flash and the copier will return
to a copy-ready state.
Setting paper on the multi-bypass tray
Standard copy paper (60 g/m² – 90 g/m²), thick paper (90 g/m² –
163 g/m²), color paper, OHP transparencies and letterhead paper
can be set on the multi-bypass tray.
ALWAYS use the multi-bypass tray when copying onto special
paper.
The sizes of paper that can be set on the multi-bypass tray are as
follows:
Inch Specification
8
1/2" × 14" (Legal) – 5 1/2" × 8 1/2" (Statement)
Metric Specification
A4 – A6R, and Folio
The types of paper and the number of sheets that can be set on the
multi-bypass tray at one time are as follows:
Standard paper (80 g/m²): 50 sheets
Thick paper (120 g/m²): 25 sheets
Thick paper (160 g/m²): 10 sheets
OHP transparencies: 1 sheet
IMPORTANT!
After setting paper on the multi-bypass tray, be sure to
use the operation panel to select the size of that paper.
(See page 3-7.)
If you want to copy onto non-standard size paper, be
sure to use the “F15” (Non-Standard Size Paper Width)
default item to register the paper size. (See page 6-2.)
When using thick copy paper (90 g/m² – 105 g/m²), be
sure to select the Thick Paper mode. (See page 3-9.)
When using OHP transparencies, be sure to use a type
of film that can withstand the heat of the fixing
process. The following products are recommended:
Arkwright (LTR)
3M PP2500 (A4)
Code number Size
-A4 A4
-A5 A5
-Fo Folio
-Lg Legal (8
1/2" × 14")
-Lt Letter (8
1/2" × 11")
-o2 Oficio II (8
1/2" × 13")
Section 3 PREPARATIONS
3-6
1 Open the multi-bypass tray towards you until you hear it
click into place.
2 Pull out the multi-bypass extension and then flip it open.
3 Adjust the insert guides to fit the width of the paper that is
to be set on the multi-bypass tray.
4 Slide the paper all the way in, along the insert guides, as
far as it will go.
IMPORTANT!
Only set paper on the multi-bypass tray when you are
planning to use that tray to feed paper. DO NOT leave
paper on the multi-bypass for long periods of time.
When you are setting paper on the multi-bypass, make
sure that the side to be copied onto is facing upward.
When using 8
1/2" × 14" (Legal), 8 1/2" × 13" (Oficio II)
or Folio size paper, it is recommended that you load
that paper into the drawer(s) and have paper fed from
there. If you do need to use the multi-bypass tray and
such paper does not feed smoothly, continue to support
the paper by its trailing edge until all of the paper has
been fed into the copier.
Section 3 PREPARATIONS
3-7
Selecting the paper size
Perform the following procedure to use the operation panel and
select the size of paper that is set on the multi-bypass tray.
There are two methods of selecting the paper size for the
multi-bypass tray: standard and temporary. The standard setting
will remain in memory even when the power switch copier is
turned OFF, while the temporary setting will be cleared each time
the power switch is turned OFF.
Selecting the paper size (standard setting)
1 Press down on the Paper Select key for at least 3 seconds.
The first default item for paper size selection will be shown.
2 Press the Number of Copies / Zoom(+) or Number of
Copies / Zoom(-) key until “F14” (Default item:
Multi-Bypass Tray Paper Size) is shown.
3 Press the Recall%/Enter key.
4 Press the Number of Copies / Zoom(+) or Number of
Copies / Zoom(-) key to select the appropriate paper size.
The displayed code numbers refer to the available paper
sizes as explained in the following table.
IMPORTANT!
If you want to copy onto non-standard size paper, be sure
to use the “F15” (Non-Standard Size Paper Width)
default item to register the paper size BEFORE
attempting to select that size. (See page 6-2.)
5 Press the Recall%/Enter key. The displayed numbers will
flash and the copier will return to a copy-ready state.
Code number Size
-A4 A4
-A5 A5
-A6 A6
-Fo Folio
-Lg Legal (8
1/2" × 14")
-Lt Letter (8
1/2" × 11")
-St Statement (5
1/2" × 8 1/2")
-o2 Oficio II (8
1/2" × 13")
XXX Non-standard size paper*
* The “XXX” shown here refers to the actual width of the
paper as registered under the “Non-Standard Size Paper
Width” default item and it is that registered number
which will be shown on the display.
Section 3 PREPARATIONS
3-8
Selecting the paper size (temporary setting)
1 Press the Paper Select key until the multi-bypass tray
indicator is lit.
2 Press the Number of Copies / Zoom(+) or Number of
Copies / Zoom(-) key to select the appropriate paper size.
The displayed code numbers refer to the available paper
sizes as explained in the following table.
IMPORTANT!
If you want to copy onto non-standard size paper, be sure
to use the “F15” (Non-Standard Size Paper Width)
default item to register the paper size BEFORE
attempting to select that size. (See page 6-2.)
3 Press the Recall%/Enter key. The copier will return to a
copy-ready state.
Code number Size
-A4 A4
-A5 A5
-A6 A6
-Fo Folio
-Lg Legal (8
1/2" × 14")
-Lt Letter (8
1/2" × 11")
-St Statement (5
1/2" × 8 1/2")
-o2 Oficio II (8
1/2" × 13")
XXX Non-standard size paper*
* The “XXX” shown here refers to the actual width of the
paper as registered under the “Non-Standard Size Paper
Width” default item and it is that registered number
which will be shown on the display.
Section 3 PREPARATIONS
3-9
Thick Paper mode
Perform the following procedure to select the Thick Paper mode
when copying onto thick copy paper (90 g/m² – 163 g/m²). When this
mode is selected, copying will be carried out at a higher fixing
temperature and the copy speed will be lowered in order to ensure
efficient fixing of the toner to the copy paper.
1 Press the Thick Paper key. The Thick Paper indicator will
light.
2 Perform the standard copying procedure.
NOTE
The copy speed will be somewhat lowered in the Thick
Paper mode.
Section 3 PREPARATIONS
3-10
When copying onto special paper, such as thick paper (90 g/m² –
163 g/m²) and OHP transparencies, ALWAYS use the face-up tray.
The face-up tray has a storage capacity of 30 sheets of standard
copy paper (80 g/m²) but only 1 sheet of special paper should be
stored there at one time.
1 Open the face-up tray (located at the rear of the copier).
2 Perform the standard copying procedure. Finished copies
will be ejected onto the face-up tray.
NOTES
Finished copies will be ejected face-up.
Copies will be stored in reverse order on the face-up
tray.
IMPORTANT!
ALWAYS be sure to close the face-up tray after use.
NEVER leave the face-up tray open.
Attaching the face-up tray
4-1
Section 4 BASIC OPERATION
1 Warm-up
Turn the power switch ON ( | ). At the end of warm-up, the
Start indicator will light.
2 Selecting the desired functions
Select from the copier’s various functions.
3 Selecting the source of paper feed
Select the location of the paper that you want to copy onto.
Press the Paper Select key to select either the upper
drawer, the Paper Feeder (option) or the multi-bypass tray.
NOTE
It is possible for you to change the default setting for
which drawer will be automatically selected.
4 Selecting the image quality
The image quality mode can be selected according to the
type of original. Press the image quality select key to light
the indicator for one of the following image quality modes.
Auto Exposure Adjustment mode: Make sure the Auto Exp.
indicator is lit.
Text & Photo mode (Originals with both text and photos):
Make sure the Text & Photo indicator is lit.
Photo mode (Originals with mainly photos): Make sure the
Photo indicator is lit.
Text mode (Originals with mainly text): Make sure the Text
indicator is lit.
Selecting the Eco-Copy indicator, and thereby the Eco-Copy
mode, will cause the copy exposure to be lightened in order
to save on toner use.
Select this mode only when high quality copies are not
required.
NOTES
It is possible for you to adjust the default copy
exposure in each of the image quality modes.
It is also possible for you to select which image quality
mode will be the default setting in the initial mode.
Basic copying procedure
Section 4 BASIC OPERATION
4-2
5 Adjusting the copy exposure
The copy exposure can be manually adjusted in all of the
image quality modes, except for the Auto Exposure
Adjustment mode. If you want to make the exposure
darker, press the right exposure adjustment key to move
the lit indicator to the right. If you want to make the
exposure lighter, press the left exposure adjustment key to
move the lit indicator to the left.
NOTE
The copy exposure scale can be set to either 5 or 7 levels
of adjustment.
6 Setting the number of copies to be made
Press the Number of Copies / Zoom(+) key if you want to
increase the number of copies to be made and the Number
of Copies / Zoom(-) key if you want to decrease the number
of copies to be made. You can also press the Number of
Copies / Zoom(-) key for at least 3 seconds to shift the
number of copies to be made from1 up to “99” in one step,
or the Number of Copies / Zoom(+) key to shift the number
of copies to be made from “99” to “1”. Make sure the desired
number of copies to be made is shown on the copy
quantity/magnification display. The setting can be made to
any number up to “99”.
NOTE
It is possible for you to limit the number of copies or copy
sets that can be made at one time.
7 Setting an original
Open the original cover and set the original that you want
to copy face-down onto the platen. Be sure to align the
original flush up against the left rear corner of the platen.
NOTES
If the optional Document Processor is installed on your
copier, set the original(s) in the Document Processor.
Shadows may appear around the edges and up the
middle of copies made from open-faced originals (such
as books, etc.).
When the copier is in a copy-ready state, the optical
lamp will be lit. This does NOT indicate trouble with
the copier.
8 Start copying
Press the Start key. Copying will begin immediately once
the Start indicator is lit green.
Section 4 BASIC OPERATION
4-3
9 At the end of copying
Finished copies will be ejected onto the copy storage table.
NOTE
The copy storage table has a storage capacity of 150
sheets of standard copy paper (80 g/m²).
CAUTION
If the copier will not be used for a short period of
time (overnight, etc.), turn the power switch
OFF ({).
If it will not be used for an extended period of time
(vacations, etc.), remove the power plug from the
outlet for safety purposes during the time the
copier is not in use.
Section 4 BASIC OPERATION
4-4
Zoom mode
With this mode, the magnification ratio can be set to any 1%
increment between 50% and 200%.
1 Press the Recall%/Enter key. The magnification ratio will
be shown on copy quantity/magnification display and the
“%” symbol will light.
2 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key, as appropriate, to change the
displayed magnification ratio to the desired ratio.
3 Press the Recall%/Enter key. The new magnification ratio
will be registered and the copy quantity/magnification
display will return to showing the number of copies to be
made.
Making enlarged and reduced copies
50%
200%
Section 4 BASIC OPERATION
4-5
Preset Zoom mode
With this mode, the magnification ratio can be set to one of the
pre-set ratios:
1 Press the Reduce/Enlarge key. The magnification ratio will
be shown on copy quantity/magnification display and the
“%” symbol will light.
2 Press the Reduce/Enlarge key again until the desired
magnification ratio is shown. The next available
magnification ratio will be shown, in order, each time you
press the Reduce/Enlarge key.
NOTE
The available magnification ratios will be shown in the
following order: “100%”, “78%”, “70%”, “50%”, “200%”,
“141%” and then “129%”.
3 Press the Recall%/Enter key. The new magnification ratio
will be registered and the copy quantity/magnification
display will return to showing the number of copies to be
made.
Available magnification ratios
(in the order they can be scrolled through*)
* After the “129%” setting, the display will return to the first
setting and show “100%”.
100%: (default setting)
78%: 8
1/2" × 14" Æ 8 1/2" × 11"
70%: A4 Æ A5
50%:
200%:
141%: A5 Æ A4
129%: 8
1/2" × 5 1/2" Æ 8 1/2" × 11"
Section 4 BASIC OPERATION
4-6
5-1
Section 5 COPY FUNCTIONS
With this mode, the images from either 2 or 4 originals can be
reduced and then combined onto a single copy. In addition, the
borderline of each original can also be marked with a solid or
dotted line.
NOTES
It is possible for you to change the default setting for
the borderline. (See “Selecting the borderline” on
page 5-6.)
Inch specification
•Only Letter (8
1/2" × 11") and Statement (5 1/2" × 8 1/2")
size originals can be used in this mode.
•Only Letter (8
1/2" × 11") size copy paper can be used in
this mode.
Metric specification
Only A4 and A5 size originals can be used in this
mode.
Only A4 size copy paper can be used in this mode.
2-in-1
Use this mode when you want to copy two originals onto each sheet
of copy paper.
Layout modes
Original Copy
Section 5 COPY FUNCTIONS
5-2
Caution on setting the originals
The following illustrations indicate how the orientation of the original will affect the resulting copies.
<When setting the originals on the platen>
NOTE
Make sure the originals are set so that the first page is scanned first.
Section 5 COPY FUNCTIONS
5-3
<When setting the originals in the Document Processor>
NOTE
Make sure the originals are set so that the first page is scanned first.
Section 5 COPY FUNCTIONS
5-4
1 Press the 2in1/4in1 key until the 2in1 indicator lights.
NOTE
It is possible for you to change the type of borderline.
(See “Selecting the borderline” on page 5-6.)
2 Set the original(s).
3 Press the Start key. Scanning of the first original will start.
NOTE
If the optional Document Processor is installed on your
copier, all of the originals set there will be scanned and
the copy operation will start.
4 Once scanning of the first original is completed, “1-” (the
number of originals already scanned) will be shown. Set the
next original and press the Start key. Carry out this step as
well for the rest of the originals that you want to copy.
5 Once you have finished scanning all of the originals, press
the Recall%/Enter key or the 2in1/4in1 key.
Copying will start.
Section 5 COPY FUNCTIONS
5-5
4-in-1
Use this mode when you want to copy four originals onto each sheet
of copy paper.
Caution on setting the originals
Be sure to set the originals as shown in the following illustrations.
<When setting the originals on the platen>
<When setting the originals in the Document
Processor>
NOTES
Make sure the originals are set so that the first page is
scanned first.
It is possible to select the order in which the images
will appear within the copy page. (See “Selecting the
order of 4-in-1 layout” on page 5-7.)
1 Press the 2in1/4in1 key until the 4in1 indicator lights.
NOTE
It is possible for you to change the type of borderline.
(See “Selecting the borderline” on page 5-6.)
2 Set the original(s).
Original Copy
Section 5 COPY FUNCTIONS
5-6
3 Press the Start key. Scanning of the first original will start.
NOTE
If the optional Document Processor is installed on your
copier, all of the originals set there will be scanned and
the copy operation will start.
4 Once scanning of the first original is completed, “1-” (the
number of originals already scanned) will be shown. Set the
next original and press the Start key. Carry out this step as
well for the rest of the originals that you want to copy.
5 Once you have finished scanning all of the originals, press
the Recall%/Enter key or the 2in1/4in1 key.
Copying will start.
Selecting the borderline
Perform the following procedure when you want to change the type
of borderline.
1 Press down on the 2in1/4in1 key for at least 3 seconds.
2 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key until “F18” (Default item: Borderline)
is shown.
3 Press the Recall%/Enter key.
Section 5 COPY FUNCTIONS
5-7
4 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key to select the desired borderline.
The displayed code numbers refer to the available
borderline types as explained in the following table.
5 Press the Recall%/Enter key.
The displayed numbers will flash and the copier will return
to a copy-ready state.
Selecting the order of 4-in-1 layout
Perform the following procedure if you want to select the order in
which the images will appear within the copy page in the 4-in-1
mode.
1 Press down on the 2in1/4in1 key for at least 3 seconds.
2 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key until “F17” (Default item: 4-in-1
Layout Order) is shown.
3 Press the Recall%/Enter key.
Code number Borderline types
1- None
2- Solid line
3- Dotted line
1-:
12
34
3-:
12
34
2-:
13
24
4-:
13
24
Section 5 COPY FUNCTIONS
5-8
4 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key until the number that corresponds to
desired layout order (1 – 4) is shown. The displayed code
numbers refer to the available layout orders as explained in
the following table.
5 Press the Recall%/Enter key.
The displayed numbers will flash and the copier will return
to a copy-ready state.
1-:
12
34
3-:
12
34
2-:
13
24
4-:
13
24
Section 5 COPY FUNCTIONS
5-9
Multiple originals can be scanned into memory in a single
operation and then the desired number of copy sets created.
1 Press the Sort key to light the Sort indicator.
2 Set the original(s).
3 Press the Start key. Scanning of the first original will start.
NOTES
If the optional Document Processor is installed on your
copier, the Sort mode will be selected automatically
once originals are set there.
If the optional Document Processor is installed on your
copier, all of the originals set there will be scanned and
the copy operation will start.
4 Once scanning of the first original is completed, “1-” (the
number of originals already scanned) will be shown. Set the
next original and press the Start key. Carry out this step as
well for the rest of the originals that you want to copy.
5 Once all of the originals have been scanned, press the
Recall%/Enter key or the Sort key. Copying will start.
Sort mode
Original Copy
Section 5 COPY FUNCTIONS
5-10
6-1
Section 6 COPY DEFAULT SETTINGS
The state that the copier enters at the end of warm-up or when the Reset/Power key is pressed is called the “initial mode”. The modes,
functions and other settings that are automatically pre-set for use in the initial mode are called “default settings”. These default settings can
be changed as desired to suit your copying needs.
Each default item, as well as each of the available settings for each item, are represented by code numbers on the copy quantity/magnification
display. Refer to the “Available settings” column in the following tables for the code number that correspond to each setting value. The factory
default setting is indicated by an asterisk.
Available default items
Item
number
Default Description Available settings
Reference
page
F00 Quit Default Settings Quits the default settings and returns the
copier to a copy-ready state.
--- ---
F01 User Copy Setting List Prints out a list of the currently selected
default settings.
--- 6-4
F08 Black Line Correction If black lines appear on copies when you feed
originals from the Document Processor (but
they do not exist on the originals themselves),
this function will make them less apparent.
If Black Line Correction is turned on, however,
small and/or detailed text may not be
reproduced as clearly as before, so it is
normally recommended that you do not change
this function from its factory default setting.
* Black Line Correction is not available when
the Photo mode is selected as the image
quality mode.
1-: OFF*
2-: Weak
3-: Strong
6-4
6-7
F12 Upper Drawer Paper Size Registers the size of paper that is loaded in the
drawer that is included with your copier.
-A4: A4
-A5: A5
-Fo: Folio
-Lg: Legal
-Lt: Letter
-o2: Oficio II
(Inch specification default:
Letter)
(Metric specification
default: A4)
6-4
6-7
F13 Paper Feeder Paper Size
(option)
Registers the size of paper that is loaded in the
optional Paper Feeder.
* If the optional Paper Feeder is not installed
on your copier, this default setting will not
appear.
-A4: A4
-A5: A5
-Fo: Folio
-Lg: Legal
-Lt: Letter
-o2: Oficio II
(Inch specification default:
Letter)
(Metric specification
default: A4)
6-4
6-7
Section 6 COPY DEFAULT SETTINGS
6-2
F14 Multi-Bypass Tray Paper
Size
Registers the size of paper that is to be set on
the multi-bypass tray.
* The “XXX” shown here refers to the actual
width of the paper as registered under the
Non-Standard Size Paper Width” and it
is that number which will be shown on the
display.
-A4: A4
-A5: A5
-A6: A6
-Fo: Folio
-Lg: Legal
-St: Statement
-Lt: Letter
-o2: Oficio II
XXX: Non-Standard Size
(Inch specification default:
Letter)
(Metric specification
default: A4)
6-4
6-7
F15 Non-Standard Size Paper
Width
Sets the width of the paper to be set on the
multi-bypass tray when that paper is of a
non-standard size.
* Non-standard size paper of up to 14", or
356 mm, in length can be used.
Inch specification:
4.13 – 8.50 (Default: 4.13)
Metric specification:
105 – 216 mm
(Default: 105 mm)
6-4
6-5
F21 Off Mode ON/OFF Sets whether the Off mode, which
automatically turns most of the power to the
copier off when a certain time elapses without
any operation being performed, will engage
automatically or not.
* If the Off mode interferes in any way with
your copying operations, turn this function
OFF. It is recommended, however, that you
try to set a longer time interval until the Off
mode engages before you actually turn it
OFF.
ON*
OFF
6-4
6-5
F23 Low Power Mode Time Sets the amount of time after each copy job is
finished until the Low Power mode
automatically engages.
1/5/15/30/45/60/90/120/
180/240 (minutes)
(Default: 15 minutes)
6-4
6-7
F24 Off Mode Time Sets the amount of time without any operation
being performed until the Off mode
automatically engages. It is also possible to
disable the Off mode. When the Off mode is
turned OFF, this default setting will not
appear. (See “Off Mode ON/OFF”)
* If the Off mode is turned off under the “Off
Mode ON/OFF” setting, this default setting
will not appear.
* It is recommended that you try to set a
longer time interval before the Off mode
engages if you use the copier frequently, and
to a shorter time if it is used less frequently.
* In order to disable the Off mode, see “Off
Mode ON/OFF”.
15/30/45/60/90/120/180/
240 (minutes)
(Default: 30 minutes)
6-4
6-7
F25 Alarm ON/OFF Sets whether the alarm which sounds when an
error occurs, etc., will be turned ON or OFF.
ON
OFF*
6-4
6-5
F26 Document Processor
Leading Edge Timing
Adjustment
Adjusts the location of the copied image if it is
shifted off-center (either forward or backward)
when the Document Processor is used to make
copies.
* If the optional Document Processor is not
installed on your copier, this default setting
will not appear.
-32 – 32 (1-step
increments)
(Each one-step adjustment
is equal to a 0.3 mm shift.)
(Adjustment is complete
at the time of purchase.)
6-4
6-9
F27 Upper Drawer Skewed
Feed Adjustment
Adjusts for off-center printing. -1.0 – 3.0 (mm)
(Adjustment is complete
at the time of purchase.)
6-4
6-6
Item
number
Default Description Available settings
Reference
page
Section 6 COPY DEFAULT SETTINGS
6-3
F28 Paper Feeder Skewed
Feed Adjustment (option)
Adjusts for off-center printing.
* If the optional Paper Feeder is not installed
on your copier, this default setting will not
appear.
-1.0 – 3.0 (mm)
(Adjustment is complete
at the time of purchase.)
6-4
6-6
F29 Multi-Bypass Tray
Skewed Feed Adjustment
Adjusts for off-center printing. -1.0 – 3.0 (mm)
(Adjustment is complete
at the time of purchase.)
6-4
6-6
F30 Document Processor
Skewed Feed Adjustment
(option)
Adjusts for skewed feeding of originals in the
Document Processor.
* If the optional Document Processor is not
installed on your copier, this default setting
will not appear.
-6.6 – 6.6 (mm)
(Adjustment is complete
at the time of purchase.)
6-4
6-8
F31 Folio Width Adjustment Sets the width (short edge) of Folio size paper. 200 – 216 (mm)
(Default: 210 mm)
6-4
6-6
F32 Toner Coverage Report Prints out a report that shows the number of
copies made and average amount of toner
used.
--- 6-4
Item
number
Default Description Available settings
Reference
page
Section 6 COPY DEFAULT SETTINGS
6-4
NOTE
If you want to access the “F30” default item (Document
Processor Skewed Feed Adjustment), proceed directly to
step 18. To access the “F26” default item (Document
Processor Leading Edge Timing Adjustment), proceed
directly to step 26.
1 Press down on both exposure adjustment keys for at least 3
seconds. The “F00” default item number will appear on the
copy quantity/magnification display.
(F01 – F32)
2 The default item number will change each time you press
the Number of Copies / Zoom(+) or the Number of Copies /
Zoom(-) key. Refer to the tables under “Available default
items” on page 6-1 to select the number that corresponds to
the desired default item.
(F01 – F32)
3 Press the Recall%/Enter key.
If you selected default items “F01” or “F32”: The
corresponding list/report will be printed out. Proceed to
step 4.
If you selected default items “F21” or “F25”: Proceed to step
5.
If you selected default item “F15”: Proceed to step 7.
If you selected default items “F27”, “F28” or “F29”: Proceed
to step 9.
If you selected default item “F31”: Proceed to step 13.
If you selected any default items other than the above:
Proceed to step 15.
(F01, F08, F12 – F15, F21, F23 – F25, F27 – F29, F31 and
F32)
4 Once the list or report is printed out, the operation panel
will return to the display in step 2. Once you are finished
accessing default items, proceed to step 17.
(F01 and F32)
NOTE
If you are going to print out a list or report, make sure
that there is 8
1/2" × 11" (Letter) or A4 paper either
loaded in a drawer or set on the multi-bypass tray.
Accessing and changing the default settings
Section 6 COPY DEFAULT SETTINGS
6-5
Sample User Copy Setting List
Sample Toner Coverage Report
5 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key to select either ON or OFF.
(F21 and F25)
6 Press the Recall%/Enter key. The operation panel will
return to the display in step 2. Once you are finished
accessing default items, proceed to step 17.
7 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key to set the width of the paper. It is
possible to enter any number between 4.13" – 8.50"
(105 mm – 216 mm).
(F15)
Section 6 COPY DEFAULT SETTINGS
6-6
8 Press the Recall%/Enter key. The operation panel will
return to the display in step 2. Once you are finished
accessing default items, proceed to step 17.
9 Press the Start key. A pattern like that shown in the
following illustration will be printed out.
(F27, F28 and F29)
NOTE
Be sure that there is 8 1/2" × 11" (Letter) or A4 size paper
in the location (a drawer or the multi-bypass tray) to be
adjusted.
10 Fold the printed sheet up the middle and compare the true
center with the printed center line.
11 If the result is as shown in example (1), increase the
setting. If the result is as shown in example (2), decrease
the setting.
NOTE
For each tenth (0.1) that you increase the setting, the
image will be moved 0.1 mm to the left.
12 Press the Recall%/Enter key. If you are finished making
adjustments, press the Stop/Clear key. The operation panel
will return to the display in step 2. Once you are finished
accessing default items, proceed to step 17.
13 Press the Number of Copies / Zoom(+) or the Number of
Copies / Zoom(-) key to set the width (short edge) of Folio
paper (200 mm – 216 mm).
(F31)
14 Press the Recall%/Enter key. The operation panel will
return to the display in step 2. Once you are finished
accessing default items, proceed to step 17.
(printed center line)
(1)
(2)
+
Section 6 COPY DEFAULT SETTINGS
6-7
15 The selected setting will change each time you press the
Number of Copies / Zoom(+) or the Number of Copies /
Zoom(-) key. Refer to the tables under “Available default
items” on page 6-1 to select the number that corresponds to
the desired default setting.
(F08, F12 – F14, F23 and F24)
16 Press the Recall%/Enter key. The operation panel will
return to the display in step 2. Once you are finished
accessing default items, proceed to the next step.
17 Press the Reset/Power key. The copier will return to a
copy-ready state.
18 Prior to performing the adjustment procedure, it is
necessary to use the Document Processor to make copies in
a standard copy mode in order to check the amount of
skewed feed that is produced.
This procedure assumes that you are using the pattern that
is printed out using the “F27” default item (Upper Drawer
Skewed Feed Adjustment) as an original.
(F30)
19 Select a standard copy mode and set the original in the
Document Processor. Set the original into the Document
Processor in the direction shown in the illustration and
make a copy.
20 Refer to steps 1 and 2 and access the actual “F30” default
item.
21 Press the Recall%/Enter key.
22 Fold the printed sheet (that you made in step 19) up the
middle and compare the true center with the printed center
line.
(printed center line)
Section 6 COPY DEFAULT SETTINGS
6-8
23 If the result is as shown in example (1), increase the
setting. If the result is as shown in example (2), decrease
the setting.
NOTE
For each tenth (0.1) that you increase the setting, the
image will be moved 0.1 mm to the right.
24 Press the Recall%/Enter key. The operation panel will
return to the display in step 2.
25 Press the Reset/Power key. The copier will return to a
copy-ready state.
NOTE
Use the Document Processor to make another copy and,
if further adjustment is necessary, repeat steps 20
through 25.
26 Prior to performing the adjustment procedure, it is
necessary to use the Document Processor to make copies in
a standard copy mode in order to check the amount of shift
that is produced.
This procedure assumes that you are using the pattern that
is printed out using the “F27” default item (Upper Drawer
Skewed Feed Adjustment) as an original.
(F26)
27 Select a standard copy mode and set the original in the
Document Processor. Set the original into the Document
Processor in the direction shown in the illustration and
make a copy.
28 Refer to steps 1 and 2 and access the actual “F26” default
item.
29 Press the Recall%/Enter key.
(1)
(2)
+
Section 6 COPY DEFAULT SETTINGS
6-9
30 Arrange the original and copy one on top of the other to
verify the direction and amount of the shift.
If the result is as shown in example (1), increase the
setting. If the result is as shown in example (2), decrease
the setting.
NOTE
It is possible to change the setting to any number (step)
between -32 - 32. Each one-step adjustment is equal to a
0.3 mm shift.
31 Press the Recall%/Enter key. The operation panel will
return to the display in step 2.
32 Press the Reset/Power key. The copier will return to a
copy-ready state.
NOTE
Use the Document Processor to make another copy and,
if further adjustment is necessary, repeat steps 28
through 32.
(1)
(2)
+
Section 6 COPY DEFAULT SETTINGS
6-10
It is possible to use the operation panel to check the total number of
copies made. It is also possible to print out that information in the
form of a report.
1 Press down on the Stop/Clear key for at least 3 seconds.
The copy count will begin to be shown on the copy quantity/
magnification display.
2 The copy count will be shown in three portions in the
following order. (In this example, the total number of copies
made is 1,234.)
NOTE
If you press the Start key while the total copy count is
being shown, the Total Count Report will be printed out.
If you are going to print out the Total Count Report,
make sure that there is 8
1/2" × 11" (Letter) or A4 paper
either loaded in a drawer or set on the multi-bypass tray.
Sample Total Count Report
3 Once the total copy count has been shown, the copier will
return to a copy-ready state.
Checking the total copy count and printing out a report
(1) (2) (3)
7-1
Section 7 TROUBLESHOOTING
When any of the following indications appears on the copy quantity/magnification display, perform the corresponding procedure.
If one of the following indications is displayed
Indication Procedure
Reference
Page
“E07” appears on the copy quantity/
magnification display
The size of paper registered in the default settings is different than the
size of the paper actually used. Check the paper size.
Pull out the corresponding drawer and then push it back in to delete the
error indications.
3-1
“E11” appears on the copy quantity/
magnification display
The Paper Feeder was selected, but the upper drawer is not installed or is
not inserted properly.
Push the upper drawer securely into the copier.
“E12” appears on the copy quantity/
magnification display
When printing out a list or report, there was no 8
1/2" × 11" or A4 size
paper available.
Press the Paper Select key to select the source of paper feed and then
press the Start key. Print out will be performed onto paper from the
selected location.
“E31” appears on the copy quantity/
magnification display
The amount of waste toner in the copier has reach the acceptable limit.
Contact your service representative or an authorized service center.
“E32” appears on the copy quantity/
magnification display
The toner container is not installed in the copier.
Install the toner container.
8-2
“E70” appears on the copy quantity/
magnification display
If the optional Document Processor is installed on your copier, there are
originals remaining on the original table.
Remove the originals, reset them on the original table and try to copy
again.
“E71” appears on the copy quantity/
magnification display
The copier will attempt to make copies from any originals that remain
uncopied.
Reset all of the originals on the original table and try to copy again.
Section 7 TROUBLESHOOTING
7-2
“E72” appears on the copy quantity/
magnification display
Originals for another job were set in the optional Document Processor
during copying from the platen in the 2-in-1 or 4-in-1 layout mode or in
the Sort mode.
Remove the new originals from the Document Processor and, once the
copy operation for the 2-in-1 or 4-in-1 layout mode or the Sort mode is
completed, reset them on the original table and try to copy again.
“E90” appears on the copy quantity/
magnification display
The copier’s memory is full.
To copy from those originals already scanned:
Press the Recall%/Enter key and copying will begin. Once those copies
have been made, reset the originals that have not yet been copied and
press the Start key. Copying will continue.
To start the copy procedure once again from the beginning:
Press the Stop/Clear key, set a lesser number of originals and try to copy
again.
“OP” appears on the copy quantity/
magnification display
The upper front cover or the front cover to the copier is open.
Close the covers securely.
“OP1” appears on the copy quantity/
magnification display
The left cover to the Document Processor is open.
Close the cover securely.
“J” and a number appear on the copy
quantity/magnification display
A paper jam has occurred.
Refer to “If paper jams” on page 7-3 and remove the jammed paper.
7-3
The Add Toner indicator lights The toner supply has run low.
Copying will still be available for awhile, but will then become impossible.
Replace the toner container as soon as possible.
8-2
The Add Toner indicator lights and “E33”
appears on the copy quantity/magnification
display
Toner has run out so further copying is impossible.
Replace the toner container.
8-2
“C” and a number appear on the copy
quantity/magnification display
Turn the power switch OFF ({) and then back ON ( | ) again. If the error
indication does not go out, make a note of the “C” and the number. Turn
the power switch OFF ({), remove the power cord, and contact your
service representative or an authorized service center.
“A” and a number appear on the copy
quantity/magnification display
Turn the power switch OFF ({) and then back ON ( | ) again. If the error
indication does not go out, make a note of the “A” and the number. Turn
the power switch OFF ({), remove the power cord, and contact your
service representative or an authorized service center.
Indication Procedure
Reference
Page
Section 7 TROUBLESHOOTING
7-3
If a paper jam occurs, copying will stop. In this case, an indication about the jam will appear on the operation panel.
Leave the power switch ON ( | ) and refer to “Removal procedures” on page 7-4 to remove the jammed paper.
Misfeed location indicators
(1) Lights when an original jams in the Document
Processor.
(2) Lights when a paper jam has occurred either in the
multi-bypass tray or inside the copier.
(3) Lights when a paper jam has occurred in the upper
drawer.
(4) Lights when a paper jam has occurred in the Paper
Feeder.
Cautions
* Do not reuse jammed paper.
* If paper is torn during removal, be sure to remove any loose
scraps of paper from inside the copier. Failure to do so could
cause another paper jam later.
* Once all jammed paper has been removed, warm-up will begin.
The error indications will disappear as well and the copier will
return to the same settings as prior to the paper jam.
If paper jams
(1)
(2)
(3)
(4)
WARNING
High voltage is present in the charger section.
Take sufficient care when working in this area, as
there is a danger of electrical shock.
CAUTION
The copier’s fixing unit is extremely hot. Take
sufficient care when working in this area, as there
is a danger of getting burned.
Section 7 TROUBLESHOOTING
7-4
Removal procedures
Paper jam inside the copier
NOTE
If there are any finished copies on the copy storage table,
remove them first before performing this procedure.
1 Open the upper front cover.
2 Open the front cover.
3 Take the Process Unit out of the copier.
4 If the leading edge of the jammed paper is visible, pull it
out towards you.
If the paper is not visible at all, perform the “Paper jam in
a drawer” procedure.
If the paper has been fed to the rear of the copier but the
leading edge is not visible, perform thePaper jam in the
paper eject section” procedure.
5 Set the Process Unit into the copier by aligning the pins on
both sides of the Process Unit with the guides inside the
copier, and then slide the Process Unit all the way back into
the copier until it stops.
6 Close the front cover.
7 Close the upper front cover.
Section 7 TROUBLESHOOTING
7-5
Paper jam in a drawer
1 Pull out the drawer that is currently being used.
2 Remove the jammed paper.
NOTE
If a paper jam occurs in the optional Paper Feeder, the
procedure to remove jammed paper is the same as with
the included drawer.
3 Push the drawer back in firmly.
4 Open and then close the upper front cover. The error
indications will go out.
Section 7 TROUBLESHOOTING
7-6
Paper jam in the paper eject section
1 Open the face-up tray.
2 Remove the jammed paper.
3 Close the face-up tray.
4 Open and then close the upper front cover. The error
indications will go out.
CAUTION
The copier’s fixing unit is extremely hot. Take
sufficient care when working in this area, as there
is a danger of getting burned.
Section 7 TROUBLESHOOTING
7-7
Paper jam in the multi-bypass tray
1 Remove all of the paper remaining on the multi-bypass
tray.
2 Open and then close the upper front cover. The error
indications will go out.
3 Reset the paper on the multi-bypass tray.
Original jam in the optional Document
Processor
1 Remove all of the originals remaining on the original table.
2 Open the left cover to the Document Processor.
3 Remove the jammed original.
If the original is caught in the rollers or difficult to remove
at all, proceed to the next step.
4 Open the Document Processor.
Section 7 TROUBLESHOOTING
7-8
5 Remove the jammed original.
6 Close the Document Processor.
7 Reset the originals.
Section 7 TROUBLESHOOTING
7-9
If trouble occurs with your copier, carry out the applicable checkpoints and procedures indicated on the following pages. If the trouble persists,
contact your service representative or authorized service center.
If other trouble occurs
Trouble Checkpoint Procedure
Reference
Page
Nothing lights on the
operation panel when the
power switch is turned ON.
Is the power plug connected to an AC
outlet?
Connect the plug to an AC outlet.
No copies come out when the
Start key is pressed.
Is there some indication of the trouble on
the operation panel?
Check the appropriate response to that
indication and perform the corresponding
procedure.
7-1
The copies come out blank. Were the originals set correctly? When setting originals on the platen, set
them face-down.
4-2
When setting originals in the optional
Document Processor, set them face-up.
The copies come out too light. Is the copier in the Auto Exposure
Adjustment mode?
In order to adjust the overall exposure
level, perform the “Auto Exposure
Adjustment” procedure.
Is the copier in either the Photo, Text &
Photo, or Text mode?
Adjust the exposure to the correct level
using the copy exposure adjustment keys.
4-2
To adjust the overall exposure, perform
the corresponding exposure adjustment
procedure.
Is the copier in the Eco-Copy mode? Select an image quality mode other than
the Eco-Copy mode.
4-1
Is the Add Toner indicator lit? Replace the toner container. 8-2
Is the copy paper wet? Replace the copy paper with new paper. 3-1
The copies come out too dark. Is the copier in the Auto Exposure
Adjustment mode?
In order to adjust the overall exposure
level, perform the “Auto Exposure
Adjustment” procedure.
Is the copier in either the Photo, Text &
Photo, or Text mode?
Adjust the exposure to the correct level
using the copy exposure adjustment keys.
4-2
To adjust the overall exposure, perform
the corresponding exposure adjustment
procedure.
The copies are dirty. Is the platen or the optional Document
Processor dirty?
Clean the platen and/or the optional
Document Processor.
8-1
Remove the Process Unit and perform the
cleaning operation on the charger.
8-4
Section 7 TROUBLESHOOTING
7-10
Black or white vertical bands
appear on the copies.
Is the charger cleaner in its home position
(marked “CLEANER HOME POSITION”)?
Remove the Process Unit and return the
charger cleaner to its home position.
8-4
If you are using the optional Document
Processor, is the slit glass dirty?
Clean the slit glass.
It is also possible to use the Black Line
Correction function to make black lines on
the copies less apparent.
6-1
8-1
The copy image is skewed. Were the originals set correctly? When setting originals on the platen, align
them flush up against its upper left corner.
4-2
When setting originals in the optional
Document Processor, align the original
insert guides securely before setting the
originals.
Paper jams occur often. Is the copy paper loaded properly in the
drawer?
Load the paper properly. 3-1
Is the copy paper curled, folded or
wrinkled?
Replace the copy paper with new paper.
Is there any jammed paper or loose scraps
of paper remaining inside the copier?
Carry out the appropriate procedure to
remove the paper.
7-3
Does the registered paper size match the
size you are actually using?
Make sure the registered paper size
matches the size you are actually using.
3-1
The Add Toner indicator
doesn’t go out even after
replacing the toner container.
Did you shake the new toner container
enough?
Shake the toner container a number of
times.
Trouble Checkpoint Procedure
Reference
Page
8-1
Section 8 MAINTENANCE AND OPERATION
INFORMATION
Lift open the original cover and wipe the gray portion, as shown in
the illustration, with a soft cloth dampened with alcohol or mild
detergent.
IMPORTANT!
Never use thinner or other organic solvents to clean the
original cover.
If the optional Document Processor is installed on your copier, lift
open the Document Processor and wipe the gray portion, as shown
in the illustration, with a soft cloth dampened with alcohol or mild
detergent.
IMPORTANT!
Never use thinner or other organic solvents to clean
the Document Processor.
If copies appear soiled while using the optional
Document Processor, such as black lines appearing on
the copy image, the slit glass (a) is dirty. Clean the slit
glass with a dry soft cloth, or one dampened with
alcohol.
Never use water, thinner or other organic solvents to
clean the slit glass.
Cleaning the copier
CAUTION
For safety purposes, ALWAYS remove the power
plug from the outlet when performing cleaning
operations.
(a)
Section 8 MAINTENANCE AND OPERATION INFORMATION
8-2
When toner runs low, the Add Toner indicator will light. If you
continue to make copies while the Add Toner indicator is lit, “E33”
will appear on the copy quantity/magnification display and the
copier will stop. Replace the toner container right away.
In addition, you should perform the appropriate cleaning operation
whenever you replace the toner container.
1 Open the upper front cover.
2 Open the front cover.
3 Lift the Process Unit, together with the toner container, out
of the copier.
IMPORTANT!
Place the Process Unit on a clean, level surface.
The drum in the Process Unit is sensitive to light.
Never expose the drum even to normal office lighting
(500 lux) for more than five minutes.
Never stand the Process Unit on end.
Replacing the toner container
CAUTION
DO NOT attempt to incinerate the toner container.
Dangerous sparks may cause burns.
CAUTION
DO NOT attempt to force open or destroy the toner
container.
Section 8 MAINTENANCE AND OPERATION INFORMATION
8-3
4 Pull the lock lever towards you into its release position
(marked “UNLOCK”), then pull the toner container release
lever to the right as indicated by the arrow (Î) in the
illustration.
5 Gently remove the old toner container. Put it in the
supplied plastic bag and dispose of it.
6 Shake the new toner container horizontally 5 or 6 times to
ensure that the toner is evenly distributed inside.
7 Remove the orange protective seal.
8 Set the new toner container into the Process Unit.
CAUTION
DO NOT attempt to incinerate the toner container.
Dangerous sparks may cause burns.
CAUTION
DO NOT attempt to force open or destroy the toner
container.
Section 8 MAINTENANCE AND OPERATION INFORMATION
8-4
9 Hold the Process Unit stable and push on the areas marked
PUSH HERE” on the toner container, until the container
clicks into place.
10 Push the lock lever back into its locked position (away from
you).
Cleaning the charger and the registration roller
Perform the following cleaning operation whenever you replace the
toner container.
11 Slide the green-colored charger cleaner knob back and forth
2 to 3 times, then return it to its home position (marked
CLEANER HOME POSITION”).
IMPORTANT!
After cleaning, make sure you restore the charger
cleaner to its home position.
If the charger cleaner is not restored to the
CLEANER HOME POSITION”, a black band will
appear on subsequent copies.
12 Use the cleaning cloth that is supplied with the new toner
kit to wipe off any paper dust and dirt that has
accumulated on the metal registration roller (A) inside the
copier.
IMPORTANT!
While cleaning, be careful to avoid touching the black
transfer roller (B).
13 After cleaning is finished, align the pins (C) on both sides of
the Process Unit with the guides inside the copier, and slide
the Process Unit slowly back into its original position in the
copier until in stops.
(A)
(B)
(C) (C)
Section 8 MAINTENANCE AND OPERATION INFORMATION
8-5
14 Close the front cover.
15 Close the upper front cover.
After use, ALWAYS dispose of the toner container
in accordance with Federal, State and Local rules
and regulations.
Section 8 MAINTENANCE AND OPERATION INFORMATION
8-6
Main Body
Type.................................................................................Desktop
Original table .................................................................Fixed type
Copying system ..............................................................Indirect electrostatic system
Acceptable originals .......................................................Sheets of paper, books and 3-dimensional objects (Maximum size: 8
1/2" × 14" (Legal) /
Folio)
Copy sizes .......................................................................Drawer: 8
1/2" × 14" (Legal), 8 1/2" × 11" (Letter), 8 1/2" × 13" (Oficio II), A4 (vertical),
A5 (vertical), and Folio
Multi-bypass tray: 8
1/2" × 14" (Legal), 8 1/2" × 11" (Letter), 5 1/2" × 8 1/2" (Statement),
8
1/2" × 13" (Oficio II), A4 (vertical), A5 (vertical), A6 (vertical), and Folio
Print margin loss: 0.5 mm – 6.5 mm (Inch Specification)
0.5 mm – 5.5 mm (Metric Specification)
Copying speed.................................................................Same size (100%; [1:1]), 8
1/2" × 11" / A4 (vertical): 15 copies/min.
Warm-up time ................................................................Within 15 secs. (at room temperature of 73.4°F/23°C, humidity 50%)
Recovery from the Low Power mode: Within 10 secs. (at room temperature of 73.4°F/
23°C, humidity 50%)
First copy speed..............................................................Approx. 9.5 secs. (8
1/2" × 11" / A4)
Available magnification ratios.......................................Any 1% increment between 50% and 200%
Standard memory...........................................................16 MB (11 MB of Bitmapping memory and 5 MB of image storage memory)
(Approx. 30 pages of memory possible with A4, 6% black originals)
Additional memory.........................................................1 slot (16 MB, 32 MB, 64 MB or 128 MB)
Resolution .......................................................................Reading: 600 dpi × 600 dpi
Writing: 600 dpi equivalent × 600 dpi
Paper feed system ..........................................................Automatic feeding from drawer (250-sheet capacity drawer [80 g/m²]), or from the
multi-bypass tray (50 sheet capacity [80 g/m²])
Acceptable copy paper....................................................<Paper weights>
Drawer: 60 g/m² – 90 g/m² (In the Thick Paper mode: 90 g/m² – 105 g/m²)
Multi-bypass tray: 60 g/m² – 90 g/m² (In the Thick Paper mode: 90 g/m² – 163 g/m²)
<Paper types>
Drawer: Standard copy paper, recycled paper and color paper
Multi-bypass tray: Standard copy paper, recycled paper, color paper, OHP
transparencies and letterhead
Continuous copying........................................................1 – 99 sheets
Light source ....................................................................Cold cathode lamp
Developing system..........................................................Single element reversing process
Fixing system .................................................................Heat roller
Cleaning system .............................................................Blade
Photoconductor ...............................................................OPC
Standard functions and modes ......................................Auto Exposure Adjustment, Eco-Copy mode, Zoom mode, Preset Zoom mode, Off Mode,
Low Power mode, Layout modes, Sort mode and Program function
Power source...................................................................120V AC, 60 Hz, 7.3 A
220V – 240V AC, 50/60 Hz, 3.8 A
Power consumption ........................................................Maximum rated power consumption 854 W
Dimensions (W) × (D) × (H) ...........................................19
9/16" × 16 5/8" × 15 3/16"
496 mm × 421 mm × 385 mm
Weight.............................................................................Approx. 30.8 lbs. / Approx. 14 kg
Noise emission................................................................ 70 dB(A)
Required space (W) × (D) ...............................................19
9/16" × 29 3/16"
496 mm × 740 mm
Optional equipment .......................................................Paper Feeder, Document Processor and Additional Memory
(Specifications are subject to change without notice.)
Specifications
Section 8 MAINTENANCE AND OPERATION INFORMATION
8-7
Document Processor (option)
Original feed system......................................................Automatic feeding
Acceptable originals.......................................................Sheets of paper
Original sizes .................................................................Max.: 8
1/2" × 14" (Legal) and Folio
Min.: 5
1/2" × 8 1/2" (Statement) and A5R
Original paper weight....................................................50 g/m² – 120 g/m²
Acceptable number of originals.....................................Maximum of 50 (50 g/m² – 80 g/m²)
Power source .................................................................. Via electrical connection to the copier
Dimensions (W) × (D) × (H)...........................................17
15/16" × 13 1/16" × 3 11/16"
455 mm × 331 mm × 93 mm
Weight ............................................................................Approx. 5.06 lbs. / Approx. 2.3 kg
(Specifications are subject to change without notice.)
Paper Feeder (option)
Paper feed system ..........................................................Automatic feeding from drawer (250-sheet capacity drawer [80 g/m²])
Paper sizes...................................................................... 8
1/2" × 14" (Legal), 8 1/2" × 11" (Letter), 8 1/2" × 13" (Oficio II), A4 (vertical), A5 (vertical)
and Folio
Acceptable copy paper ...................................................<Paper weights>
60 g/m² – 90 g/m² (In the Thick Paper mode: 90 g/m² – 105 g/m²)
<Paper types>
Standard copy paper, recycled paper and color paper
Power source .................................................................. Via electrical connection to the copier
Dimensions (W) × (D) × (H)...........................................14
7/8" × 14 3/4" × 3 1/8"
378 mm × 375 mm × 79 mm
Weight ............................................................................Approx. 4
7/16 lbs. / Approx. 2.0 kg
(Specifications are subject to change without notice.)
Additional Memory (option)
Memory type ..................................................................100-pin DIMM
Available memory ..........................................................16 MB, 32 MB, 64 MB and 128 MB
Number of scanable originals........................................16 MB: 125, 32 MB: 220, 64 MB: 250 and 128 MB: 250 (A4, 6% black)
(Specifications are subject to change without notice.)
Section 8 MAINTENANCE AND OPERATION INFORMATION
8-8
• Recovery time from the Low Power mode..................10 seconds
• Transition time to the Low Power mode
(at time of purchase) ...................................................15 minutes
• Transition time to the Off and Sleep modes
(at time of purchase) ...................................................30 minutes
Duplex (2-sided) copying
• Not available
Paper feed
• Recycled paper made from 100% recycled pulp may be used with this product.
Environmental Specifications
For best copy results and machine performance, we recommend that you use only KYOCERA
MITA original supplies for your KYOCERA MITA copier.
©2003 KYOCERA MITA CORPORATION
is a trademark of Kyocera Corporation
is a registered trademark of KYOCERA MITA CORPORATION
2003. 3
2DC80030A
74


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera km 1500 laser 15ppm at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera km 1500 laser 15ppm in the language / languages: English as an attachment in your email.

The manual is 5,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info