20377
60
Zoom out
Zoom in
Previous page
1/110
Next page
Chapter 1 Using the Operator Panel
1-50
The RAM disk is a memory space shared within the printer
memory that can temporarily store print jobs. The RAM disk
can be used only for electronic sorting. The stored print job
can then be used to print multiple copies of the job reducing
the total amount of time required to print the whole job. It
acts similar to the hard disk except that the data is effective
only during the printer is powered up. By default, the RAM
disk is not activated (Off).
To use the RAM disk, activate and enter the desired size of
the RAM disk in the manner described below. The maximum
RAM disk size can be calculated as follows:
Maximum RAM disk size = Total printer memory minus 9 MB
For example, if the total memory installed in your printer is
16 MB (factory setting), you can set 7 MB of RAM disk. If you
attempt to set the RAM disk size beyond this restriction, the
printer automatically round it down so that the size is always
9 MB less than the total printer memory. Once the RAM disk
size is set, the printer must be reset.
To activate RAM disk in the printer’s memory, first you must
set the RAM disk mode to On and set the desired data size for
the RAM disk as descriped in the following section. This al-
lows you to perform the following operations on the RAM
disk.
Reading data
•Writing data
•Deleting data
Printing a list of data names (partitions)
The operations of the RAM disk are the same as those of the
memory card. See the relevant sections in
Using the Memory
Card on page 1-46
.
• The RAM disk can not be used when an option hard disk is in-
stalled.
• The RAM disk stores data only temporarily. When the printer is
reset or turned off, the stored data will be erased.
The RAM disk is allocated within the printer’s memory available
to users. If the size of the RAM disk is set too large, the printing
speed may decrease or the memory may become insufficient.
To confirm the RAM disk size or activate the RAM disk, pro-
ceed as follows:
Setting the RAM Disk Size
Press the MENU key.
Press the or key repeatedly until RAM Disk
Mode appears.
Press the ENTER key. A blinking question mark (?)
appears. Press the or key to select On. Press
the ENTER key.
Press the key. Press the or key repeatedly
until >RAM Disk Size appears. The data size also
appears.
Press the ENTER key. A blinking cursor (_) appears.
Press the or key to display the desired size. De-
finable RAM disk size is 0001 to 1024.
This range varies depending on the total memory
size of the printer. The setting exceeding this range
is automatically adjusted to the maximum RAM disk
size.
When the desired RAM disk size is displayed, press
the ENTER key.
Press the MENU key. The message display returns to
Ready. Then, turn off the printer and on again. The
selected RAM disk size is activated after the printer
is restarted.
Using the RAM Disk
NOTE
RAM Disk Mode
Off
RAM Disk Mode
? On
>RAM Disk Size
0007 MByte
>RAM Disk Size
0007
MByte
1
2
3
4
5
6
7
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera FS6020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera FS6020 in the language / languages: English as an attachment in your email.

The manual is 4,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info