20207
168
Zoom out
Zoom in
Previous page
1/182
Next page
RS-232C/RS-422A Protocol
C-11
H5: Protocol logic
H5: Protocol logicH5: Protocol logic
H5: Protocol logic
The factory setting is 0.
H6: Buffer nearly-full threshold
H6: Buffer nearly-full thresholdH6: Buffer nearly-full threshold
H6: Buffer nearly-full threshold
This is a percentage from 0 to 99. The factory setting is 90.
H7: Buffer nearly-empty threshold
H7: Buffer nearly-empty thresholdH7: Buffer nearly-empty threshold
H7: Buffer nearly-empty threshold
This is a percentage from 0 to 99. The factory setting is 70.
The factory settings of the buffer nearly-full and nearly-empty thresholds
(H6 and H7) are subject to change without notification.
The gap between the nearly-full and nearly-empty thresholds allows the
computer to send a fairly large amount of data in a continuous stream.
H8: Received-data buffer size
H8: Received-data buffer sizeH8: Received-data buffer size
H8: Received-data buffer size
This is the size of the input buffer, specified in units of 10 Kbytes. The
factory-set value is 6, meaning 60 Kbytes.
Since DTR/DSR protocol is not used with the RS-422A standard, select a
parameter value other than 0, 1, or 2 for the H5 setting when using the
RS-422A interface.
C.4.1 PRESCRIBE FRPO D0 Command
The PRESCRIBE FRPO D0 command provides control over XON/XOFF
operation when an error occurs on the serial interface. The following table
summarizes the error status corresponding to different D0 values.
Parameter value
Parameter valueParameter value
Parameter value Meaning
MeaningMeaning
Meaning
0 Combination of 1 and 3 below
1 DTR/DSR, positive logic
2 DTR/DSR, negative logic
3XON/XOFF
4 ETX/ACK
5 XON/XOFF recognized only as protocol
Note
Serial interface error
Serial interface errorSerial interface error
Serial interface error
Error not handled
Error not handledError not handled
Error not handled Error handled
Error handledError handled
Error handled
Timing of XON transfer to
host while Ready or Waiting
XON sent every 3-5 seconds D0=0 (default) D0=1
XON not sent D0=10 D0=11
168


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera FS1010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera FS1010 in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kyocera FS1010

Kyocera FS1010 User Manual - German - 24 pages

Kyocera FS1010 Installation Guide - Dutch - 24 pages

Kyocera FS1010 User Manual - French - 24 pages

Kyocera FS1010 User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info