20207
165
Zoom out
Zoom in
Previous page
1/182
Next page
Serial Interface (Option)
C-8
SG - Signal Ground - (Pin 7)
SG - Signal Ground - (Pin 7)SG - Signal Ground - (Pin 7)
SG - Signal Ground - (Pin 7)
All signals can transmit between the printer and the host computer to send
each signal with a signal ground.
DTR - Data Terminal Ready - (Pin 20)
DTR - Data Terminal Ready - (Pin 20)DTR - Data Terminal Ready - (Pin 20)
DTR - Data Terminal Ready - (Pin 20)
This output is used as a buffer nearly-full handshake line. It is held high
(above 3 volts) when the buffer can accept more data.
RS-232C Interface Voltage Levels
RS-232C Interface Voltage LevelsRS-232C Interface Voltage Levels
RS-232C Interface Voltage Levels
The voltage levels of the interface signals conform to EIA RS-232C
specifications. SPACE is from 3 volts to 15 volts. MARK is from -3 volts to
-15 volts. Voltages between -3 volts and 3 volts are undefined.
C.3.2 RS-422A Interface
The serial interface is set to the RS-232C mode as the factory default.
However, by changing the jumper connector on the IB-10E interface board,
the interface can be changed to the RS-422A mode.
In the RS-232C mode
In the RS-232C modeIn the RS-232C mode
In the RS-232C mode, the printer can be connected to a personal computer
(or similar device) equipped with an RS-232C serial interface. (The serial
interface is set to the RS-232C mode as the factory default.)
In the RS-422A mode
In the RS-422A modeIn the RS-422A mode
In the RS-422A mode, the printer can be connected to a personal computer
(or similar device) equipped with an RS-422A serial interface.
Changing of the jumper connector should be carried out only by a
Kyocera Mita authorized dealer or Kyocera Mita certified technician.
Kyocera Mita shall not be liable for damage due to improper changing of
the jumper connector.
Interface Signals
The pins in the printer’s RS-422A interface connector carry the signals
listed in
Table C.4
Table C.4Table C.4
Table C.4
.
Table C.4 RS-422A Signal Pin Assignments
Note
Pin
PinPin
Pin In/out
In/outIn/out
In/out Signal
SignalSignal
Signal Description
DescriptionDescription
Description
1 - FG Frame ground
3 In RDA Receive data Inverted
7 - SG Signal ground
9 Out SDA Send data Inverted
10 Out SDB Send data
11 - - +5V DC
18 In RDB Receive data
165


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera FS1010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera FS1010 in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kyocera FS1010

Kyocera FS1010 User Manual - German - 24 pages

Kyocera FS1010 Installation Guide - Dutch - 24 pages

Kyocera FS1010 User Manual - French - 24 pages

Kyocera FS1010 User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info