20207
161
Zoom out
Zoom in
Previous page
1/182
Next page
Parallel Interface
C-4
Detailed descriptions of the signals follow.
Strobe* [nStrobe] (Pin 1)
Strobe* [nStrobe] (Pin 1)Strobe* [nStrobe] (Pin 1)
Strobe* [nStrobe] (Pin 1)
A negative-going Strobe* pulse causes the printer to read and latch the
data on the Data 0 [1] to Data 7 [8] signal lines.
Data 0 [1] to Data 7 [8] (Pins 2 to 9)
Data 0 [1] to Data 7 [8] (Pins 2 to 9)Data 0 [1] to Data 7 [8] (Pins 2 to 9)
Data 0 [1] to Data 7 [8] (Pins 2 to 9)
These eight signals form the data byte sent from the host computer to the
printer. Data 7 [8] is the most significant bit.
Acknowledge* [nAck] (Pin 10)
Acknowledge* [nAck] (Pin 10)Acknowledge* [nAck] (Pin 10)
Acknowledge* [nAck] (Pin 10)
This negative-going pulse acknowledges the previous character received by
the printer.
Busy [Busy] (Pin 11)
Busy [Busy] (Pin 11)Busy [Busy] (Pin 11)
Busy [Busy] (Pin 11)
This signal is high when the printer is busy and low when it is able to
accept more data.
Paper Empty [PError] (Pin 12)
Paper Empty [PError] (Pin 12)Paper Empty [PError] (Pin 12)
Paper Empty [PError] (Pin 12)
This signal goes high when the printer runs out of paper.
Online [Select] (Pin 13)
Online [Select] (Pin 13)Online [Select] (Pin 13)
Online [Select] (Pin 13)
This signal is high when the printer is online and low when the printer is
offline. It goes low when the upper unit is raised, or when the key is
pressed to set the printer offline.
The Paper Empty and Online signals are not used unless enabled by the
FRPO command (O2 parameter).
+5V DC (pin 18)
+5V DC (pin 18)+5V DC (pin 18)
+5V DC (pin 18)
This line is connected to the printer’s +5V DC line (+5 V ±0.5 V, maximum
400 mA, fused.)
Reset [nInit] (Pin 31)
Reset [nInit] (Pin 31)Reset [nInit] (Pin 31)
Reset [nInit] (Pin 31)
This signal is used in the standard Centronics interface to enable the
computer to reset the printer.
Error* [nFault] (Pin 32)
Error* [nFault] (Pin 32)Error* [nFault] (Pin 32)
Error* [nFault] (Pin 32)
When the high-speed parallel line control is on (FRPO O2=2), this line
returns error status.
Auxiliary output 1 (Pin 33)
Auxiliary output 1 (Pin 33)Auxiliary output 1 (Pin 33)
Auxiliary output 1 (Pin 33)
This signal line is not used.
Note
161


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera FS1010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera FS1010 in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kyocera FS1010

Kyocera FS1010 User Manual - German - 24 pages

Kyocera FS1010 Installation Guide - Dutch - 24 pages

Kyocera FS1010 User Manual - French - 24 pages

Kyocera FS1010 User Manual - Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info