512522
172
Zoom out
Zoom in
Previous page
1/186
Next page
Introduction Getting Ready
Taking Pictures
Playback Set Up
GB-172
Troubleshooting
NEXT
Contents (Top page) Detailed Contents Index Nomenclature Menus and Settings Troubleshooting
Troubleshooting
Check the items listed below before deciding that your camera is faulty.
Problems and Solutions
Problem Cause Solution
Nothing appears on
the LCD monitor.
The batteries are flat or not inserted. Load unused or charged batteries into
the camera.
The Power Save function has turned
the camera off. (Æ
p.152)
Press the POWER button H again
to turn the camera back on.
The LCD monitor is
blank.
EVF (electronic viewfinder) is
selected in the [SELECT LCD]
setting.
Press the VF button V to select
the [LCD] monitor display.
If you leave the camera for a while
without using it, the camera goes into
Sleep mode.
Press the shutter release button half
way or press any other camera button to
restore the camera to Shooting mode.
The details vary depending on the
Power Save function settings. (
Æ
p.152)
There is something generating a
magnetic field (such as a magnet or
TV) close to the camera.
Move the camera further away from
the magnetic object.
The video cable is connected to the
camera.
Disconnect the video cable.
There's no image
on the TV.
You are using the wrong video output
format.
Use the correct video output format for
the TV. (Æ
p.163)
The number of
available shots did
not change when I
took a picture.
This is because the photographed
image size was small.
This is dependent on factors such as
the quality mode and the subject and
is not a problem.
I cannot erase an
image. "U" icon
displayed.
The image is protected. Unprotect the image. (Æ
p.107)
The number of
available shots did
not increase after I
erased an image.
This is because the erased image
size was small.
This is dependent on factors such as
the quality mode and the subject and
is not a problem.
The camera feels
hot.
Because the LCD monitor uses
relatively large amounts of current,
the camera grows warm after
prolonged use.
This is not a problem, but you should
shut the camera down for a few
minutes.
172


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera Finecam M410R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera Finecam M410R in the language / languages: English as an attachment in your email.

The manual is 8,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info