522406
7
Zoom out
Zoom in
Previous page
1/29
Next page
7
Follow these steps to connect the data/power
and RF cables to the antenna.
a. Route the data/power and RF cables
belowdecks through the cable access hole.
Leave an adequate service loop,
approximately 8" (20 cm) of slack, in the
cables for easy serviceability. Later, you will
connect the data/power cable to the MCU
and the RF cable(s) to the receiver(s).
b. Position the antenna in place over the
mounting holes with the baseplate’s
connectors (see Figure 11) facing the stern.
c. Connect the data/power cable to the antenna
(see Figure 12 and Figure 13); hand-tighten.
d. Using a 9/16" wrench, connect the RF cable(s)
to the antenna. If you need to connect only
one RF cable, connect the cable to the
antenna’s RF1 connector (see Figure 13).
Connect any additional RF cables to the RF2,
RF3, and RF4 connectors.
TIP: If you connect two or more RF cables, label
both ends of each cable to match the connector.
This will make it easier to identify the cables later.
e. Place the rear logo plate over the cables, so
each cable exits the proper opening (see
Figure 14). Using six M4 screws, attach the
logo plate to the baseplate.
If you wish to route the cables through the
bottom of the antenna’s baseplate, rather than
connecting at the side, see Appendix A on
page 23 for supplemental instructions.
IMPORTANT!
Be sure to properly align the data/power
cable with the antenna’s baseplate connector
before tightening. Connecting the cable at an
angle may damage the cable’s center lines.
IMPORTANT!
Wire the Antenna
Figure 11 Antenna Connectors
Figure 12 Data/power Cable Connections
Figure 13 Antenna Baseplate Cable Connections
Figure 14 Rear Logo Plate Installed
Connectors
F-type Connector N-type Connector
MCU Antenna
Data/
Power
RF3 RF1 RF2 RF4
Data/
Power
RF1
M4 Screw (x6)
5
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for KVH TracVision M9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of KVH TracVision M9 in the language / languages: English as an attachment in your email.

The manual is 7,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of KVH TracVision M9

KVH TracVision M9 User Manual - English - 73 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info