522403
6
Zoom out
Zoom in
Previous page
1/17
Next page
6
Follow these steps to connect the antenna cable to
the antenna.
a. Using the supplied 3 mm Allen hex key,
remove the connector cover from the
antenna’s base (see Figure 7). Save the cover
and the four M4 cap screws for later use.
b. Route the antenna cable belowdecks through
the cable access hole. Be sure to keep the end
of the cable with the rubber sealing boot at
the antenna site.
c. If you are routing the cable underneath the
antenna, attach the right-angle connector to
the antenna end of the cable. Hand-tighten,
then tighten with a 7/16" wrench for 1/4 turn
to ensure an electrical and weather-proof
connection. Then place the supplied right-
angle rubber boot extension onto the end of
the cable (see Figure 8).
d. Connect the cable to the antenna. Hand-
tighten, then tighten with a 7/16" wrench for
1/4 turn (see Figure 9).
e. If you are using a right-angle connector, slide
the right-angle rubber boot extension up the
cable until it covers the right-angle connector.
f. Slide the rubber boot up the cable until it
covers the connector. If you are using a right-
angle connector, be sure the boot mates with
the extension (see Figure 10). This boot will
help protect the connector from the elements.
g. Reattach the cover over the connector, as
shown in Figure 10. Secure in place with the
M4 cap screws you removed in Step a. The
cover must be attached before you mount the
antenna.
h. Leave an adequate service loop,
approximately 8" (20 cm) of slack, in the
antenna cable for easy serviceability.
i. Weatherproof and seal the cable access hole
as required.
Figure 7: Removing the Connector Cover
Right-Angle
Connector Extension Rubber Boot
Figure 8: Rubber Boot Extension for Right-Angle Connector
Figure 9: Connecting the Antenna Cable
Right-Angle
Boot Extension
(if necessary)
Rubber Boot
Cover
Figure 10: Protecting the Cable Connection
Be sure to seal the cable access hole to prevent
water from leaking into the vessel.
IMPORTANT!
Wire the Antenna
4
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for KVH TracVision M2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of KVH TracVision M2 in the language / languages: English as an attachment in your email.

The manual is 2,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of KVH TracVision M2

KVH TracVision M2 User Manual - English - 65 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info