Manual Kuppersbusch EWI 456.0 (page 29 of 115) (English, Dutch, French, Italian, Portuguese, Spanish)

513947

Zoom out

Zoom in

1/115

Assembly instructions

Assembly instr uctions

Note

The KÜPPERSBUSCH induction hob may only be built-in

in accordance to the instructions included in this manual:

In case of a failure to observe these instructions,

KÜPPERSBUSCH shall decline any liability and the

approved marks of conformity become invalid!

Safety instructions for kitchen unit fitters

• Veneers, adhesives and plastic surfaces of surrounding

furniture must be temperature resistant (>75°C). If the veneers

and surfaces are not sufficiently heat resistant they can

become deformed.

• Ensure that all live connections are safely insulated when

installing the hob.

• Cover strips between the wall and the worktop behind the hob

which are made of solid wood are permissible as long as

minimum clearances in accordance with the installation

diagrams are maintained.

• Minimum clearances of the hob cut-out towards the rear are to

be maintained in accordance with the installation diagram.

• For installation directly next to a tall cupboard, a safety

distance of at least 40 mm must be ensured. The side surface

of the tall cupboard should be fitted with heat resistant

material. Due to working requirements, however, the distance

should be at least 300 mm.

• The clearance between the hob and an extraction hood must

be at least as large as that stipulated in the assembly

instructions for the cooker hood.

• The packaging materials (plastic foil, polystyrene, nails etc.)

must be kept out of reach of children as these parts are

potentially dangerous. Small parts can be swallowed and there

is a danger of plastic sheeting causing suffocation.

Ventilation

• Clearance between the induction hob and kitchen furniture or

built-in units must provide for sufficient ventilation of the

induction hob.

• If the power level of a cooking zone is automatically raised or

lowered (see section on thermal cut-off device) it is likely that

the cooling system does not cool sufficiently. In this case we

recommend that the back wall of the bottom kitchen unit in the

area of the worktop cut-out be opened and that the front

transverse strip of the unit be removed over the entire width of

the appliance in order to promote the circulation of air.

Installation

Important

• Remove any transverse strips underneath the worktop at least

in the area of the worktop cut-out.

• Avoid excessive thermal development from below e.g. from a

baking oven without a cross flow cooling device.

• The induction hob may not be used when pyrolysis operation

is taking place in a built-in oven.

• When installing the appliance on top of a drawer it is essential

to ensure that no sharp items are stored in the drawer since

these could become bent on the underside of the hob and

prevent the drawer from being opened and closed.

• If a shelf has been inserted underneath the hob, there must be

a clearance of at least 20 mm to the underside of the hob in

order to ensure that the hob is sufficiently ventilated.

• The hob may not be installed above refrigerators, freezers,

dishwashers, washing machines or dryers.

• To avoid danger of fire, make sure that no combustible objects

which could easily catch fire or become deformed on exposure

to heat are directly next to or under the surface.

Sealing of the hob

Before installation, correctly insert the sealing unit delivered with

the hob.

• No liquids may penetrate between the edge of the hob and the

worktop or between the hob and the wall and come into

contact with any electrical appliances.

• When installing a hob into an uneven worktop, e.g. with a

ceramic or similar covering (tiles etc.), the seal on the hob is to

be removed and the seal between the hob and worktop made

with plastic sealing materials (putty).

•

The hob must under no circumstances be sealed with

silicone sealant!

This would make it impossible to remove the

hob at a later date without damaging it.

Working surface cut-out

Cut out the worktop recess accurately with a good, straight saw

blade or recessing machine. The cut edges should then be

sealed so that no moisture can penetrate.

The area is cut out as illustrated. The glass ceramic hob must

have a level and flush bearing. Any distortion may lead to

fracture of the glass panel. Make sure that the sealing of the hob

is properly seated.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kuppersbusch EWI 456.0 in the language / languages: English, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kuppersbusch EWI 456.0

Kuppersbusch EWI 456.0 User Manual - German - 17 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kuppersbusch EWI 456.0 Manual

Product: