639537

Kubota B2320 Manual

80
Zoom out
Zoom in
Previous page
1/88
Next page
PERIODIC SERVICE64
BChecking Radiator Hose and Clamp
Check to see if radiator hoses are properly fixed every 200
hours of operation or six months, whichever comes first.
1. If hose clamps are loose or water leaks, tighten bands
securely.
2. Replace hoses and tighten hose clamps securely, if
radiator hoses are swollen, hardened or cracked.
Replace hoses and hose clamps every 2 years or earlier
if checked and found that hoses are swollen, hardened or
cracked.
C Precaution at Overheating
Take the following actions in the event the coolant
temperature is nearly or more than the boiling point, what
is called "Overheating"
1. Park the tractor in a safe place and keep the engine
unloaded idling.
2. Don't stop the engine suddenly, but stop it after about
5 minutes of unloaded idling.
3. Keep yourself well away from the machine for further
10 minutes or while the steam blows out.
4. Check that there are no dangers such as burns. Get rid
of the causes of overheating according to the manual,
see "TROUBLESHOOTING" section, and then, start
again the engine.
BChecking Intake Air Line
1. Check to see that hoses and hose clamps are tight and
not damaged.
2. If hoses and clamps are found worn or damaged,
replace or repair them at once.
EVERY 400 HOURS
BAdjusting Front Axle Pivot [4WD]
If the front axle pivot pin adjustment is not correct, front
wheel vibration can occur causing vibration in the steering
wheel.
C Adjusting procedure
Loosen the lock nut, and tighten the adjusting screw so
that the oscillating load is 50 to 100 N (5.1 to 10.2 kgf, 11.2
to 22.5 lbf). (If the adjusting screw is tightened, loosened
and retightened, apply liquid gasket to its tip.) Retighten
the lock nut.
Consult your local KUBOTA Dealer for further details.
(1) Radiator hoses
(2) Hose clamps
(1) Hose
(2) Hose clamps
(1) Adjusting screw
(2) Lock nut
… 80 …


Need help? Post your question in this forum.

Forumrules
1

Forum

kubota-b2320

Reset search

  • my b 2320 is making a loud clicking sound from the drive line. I suspect it is a broken bearing in the transmission. Is this easily repairable
    Submitted on 29-4-2023 at 11:54

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kubota B2320 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kubota B2320 in the language / languages: English as an attachment in your email.

The manual is 5,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info