639466
2
Zoom out
Zoom in
Previous page
1/233
Next page
81700·82100·82400 WSM, 11770
(2) Wheel Hub
Pin
5
BRAKES
RearWheel
1.
Place
ajack under
the
transmission
case.
2.
Loosen
the
rear wheel cotter (1) setting
bolt
and nut.
3.
Take
out
the
wheel hub
pi
n (2).
4.
Take
out
the
rear wheel.
l1li
IMPORTANT
48
When
re-fitting
or adjusting a wheel,
tighten
the
bolts
to
the
following
torques then recheck
after
driving
the
tractor
200
m (200 yards) and there
after
daily
check service.
(When reassembling)
Rearwheel cotter
123to147N'm
Tightening torque
setting
bolt
and
nut
12.6
to
15.0
kgf'm
91
to
108 ft-Ibs
8177P168
(1) Differential Lock
Rod
(2) 8rake
Rod
(3)
Rear
Axle
Case
Rear
Axle
Case
with
Brake Assembly
1.
Disconnect
the
differential lock rod (1).
2.
Disconnect
the
brake rod (2).
3.
Remove
the
rear axle
case
mounting screw.
4.
Separate
the
rear axle
case
(3) from differential gear
case.
(When reassembling)
48
Apply liquid gasket (Three Bond 1208D
or
equivalent)
to
joint
face
of
the
rear axle
case
and
differential
gear
case
after
eliminating
the
water, oil and stuck liquid gasket.
Rear
axle
case
mounting
39
to
44 N'm
Tightening torque
4.0
to
4.5 kfl:t.m
screws
29to
33
ft-
s
Differential Lock Shift Fork and Differential Lock Clutch
1.
Remove
the
spring (1).
2.
Draw
out
the
differential lock shift
fork
(2) and
differential
lock clutch (3).
(1)
Spring
(3)
Differential
Lock
Clutch
(2)
Differential
Lock
Shift Fork
5-55
2


Need help? Post your question in this forum.

Forumrules
1

Forum

kubota-b2100

Reset search

  • My b2100 (1999) brake s work fine, but the handle to lock them doesn't work any longer. Feels like something is disconnected. Anyone have and answer or a schematic? Submitted on 23-11-2021 at 05:14

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kubota B2100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kubota B2100 in the language / languages: English as an attachment in your email.

The manual is 15,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kubota B2100

Kubota B2100 Installation Guide - English - 233 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info