639465
200
Zoom out
Zoom in
Previous page
1/233
Next page
81700·82100·82400 WSM,11772
SERVICING
CHECKING
AND
ADJUSTING
3
TRANSMISSION
8193P014
(1) 8rake
Rod
(RH)
(2)
HST
Pedal
Damper
(3) Neutral Adjuster
(4) Return Spring
(for
forward
adjustment)
(5) Return Spring
(for
reverse adjustment)
(6) Adjusting
Nut
(7) Adjusting
Nut
(8) Lock
Nut
(9) Lock
Nut
(10) Lock
Nut
(11) Neurtal Position
Adjusting
Nut
(12)
Rod
(13) Stay
Neutral
1.
Disengage the
front
wheel
drive
lever. (Drive
only
rear
wheels.)
2.
Lift
the
rear
of
the
tractor
so
that
the
rear wheels are
off
the
ground and run the engine
at
low
idling
and drive
only
rear
wheels.
3.
Depress
the
one end
of
speed control pedal and release, and
do
the
same
at
the other end.
4.
If
the
rear wheels
do
not
stop
turning,
adjust
as
following
procedure.
Adjusting Neutral
1.
Disconnect the brake rod
RH
(1).
2.
Loosen
the
lock
nut
(8)
(9)
and adjusting
nut
(6) (7)
until
springs
(4)
(5)
are freely.
3.
Loosen
the
lock
nut
(10) and neutral position adjusting
nut
(11) until washer welded on
the
rod (12) comes
off
from
stay
(13).
4.
Remove
the
HST
pedal damper (2).
5.
Loosen
the
neutral adjuster
(3)
setting screw.
(When rear wheels tend
to
turn
forward)
1.
Rotate
the
neutral adjusting lever clockwise
so
that
the
rear
wheels
turn
reverse.
2.
Then
rotate
it
counterclockwise
until
wheels
stop
completely.
(When rear wheels tend
to
turn
reverse)
1.
Rotate
the
neutral adjusting lever counterclockwise
so
that
the
rear wheels
turn
forward.
2.
Then rotate
it
clockwise until wheels stop completely.
(After
adjusting neutral)
1.
Make sure the
HST
control pedal (d)
is
at
the neutral position.
(Let the pedal
go
from
the
forward
to
the
neutral position,
as
well
as
from
the rearward
to
the
neutral position. Make sure
the pedal returns
to
just the
same
neutral position.)
2.
Turn
the
neutral position adjusting
nut
(11)
to
move
the
rod
(12) until there
is
a clearance
"A"
0 mm
(0
in.) between
the
welded washer and the stay (13). (Set in
position
with
a
slight contact.)
Now
turn
this
nut
counterclockwise by
half
a
turn.
Now
lock
the
nut
(10).
(Be
careful
not
overtighten
the
nut
(11). Otherwise the
HST
pedal may
get
stuck.)
3.
Finally lock the double
nut
(8),
(9)
so
that
the
spring (4), (5),
should
be
49
to
51
mm (1.93
to
2.01
in.)
forward
and
49
to
51
mm (1.93
to
2.01
in.) rearward in
length
Band
C.
----
Length
(B)
Length
(C)
Normal compression
50
mm (2.0 in.)
50
mm (2.0 in.)
Max. compression
42
mm (1.7 in.)
42
mm (1.7 in.)
Neutral adjuster setting
39.2
to
44.1
N'm
Tightening
torque
4.0
to
4.5
kgf'm
screw
28.9
to
32.5 ft-Ibs
E3-S1
200


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kubota B1700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kubota B1700 in the language / languages: English as an attachment in your email.

The manual is 15,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kubota B1700

Kubota B1700 Installation Guide - English - 233 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info