639465
188
Zoom out
Zoom in
Previous page
1/233
Next page
B1700'B2100'B2400 WSM,11771
6
FRONT
AXLE
Tightening
torque
Bi-speed Turn Clutch Assembly
1.
Put back the stakes
of
the
nut
(1)
and remove it.
2.
Pull
out
the ball bearing
(2)
with
a puller and remove
the
plain washer
(3)
shifter collar
(4)
and shifter
(5).
3.
Remove
the
bi-speed
turn
coupling (6), clutch discs (7),
friction plates (8), collar
(14)
and bi-speed
turn
clutch drum
(13).
4.
Remove
the thrust collar (10), bi-speed
turn
gear (11) and
inner ring
(12)
from the bi-speed turn clutch drum (13).
5.
Remove
the gear shaft (15).
(When reassembling)
Apply
molybdenum
desulphid
(Three
Bond 1901
or
equivalent)
to
the inner ring.
Replace
the staking
nut
with
a new one and tighten the
nut
and
be
sure
to
stake it.
(9) Bearing Holder
(10) Thrust Collar
(11) Bi-speed Turn Gear
(12) Inner
Ring
(13) Bi-speed Turn
Clutch Drum
(14) Collar
(15) Gear Shaft
B177P338
(1) Nut
(2) Ball Bearing
(3) Plain Washer
(4) Shifter Collar
(5) Shifter
(6) Bi-speed
turn
Coupling
(7) Clutch
Disc
(8) Friction Plate
After
installing the gear shaft
with
the bearing, reinstall
the
bi-speed
turn
clutch
ass'y.
SERVICING
[2WD TYPE]
Clearance between Center
Pin
and
Pin
Support
1.
Measure the center pin
O.D.
with
an
outside micrometer.
2.
Measure the pin support I.D.
of
the
front
axle
with
a cylinder
gauge.
3.
Ifthe
clearance
exceeds
the allowable limit, replace it.
Factory
spec.
0.05
to
0.25 mm
Clearance between
0.0020
to
0.0098 in.
center pin and pin
support
Allowable
limit
0.70mm
0.0276 in.
Center pin
0.0.
Factory
spec.
24.90
to
25.00 mm
0.9803
to
0.9842 in.
Pin
support 1.0.
Factory
spec.
25.05
to
25.15 mm
0.9862
to
0.9901 in.
Clearance between Knuckle Shaft and Bushing
1.
Measure the knuckle shaft
O.D.
at several points
with
an
outside micrometer. (The knuckle shaft
tends
to
show
concentrated wear.)
2.
Similarly, measure
the
knuckle shaft bushing I.D.
with
a
cylinder gauge.
3.
Ifthe
clearance
exceeds
the allowable limit, replace.
Factory
spec.
0.040
to
0.105 mm
Clearance between
0.0016toO.0041 in.
knuckle shaft and
bushing
Allowable
limit
0.50
mm
0.0197 in.
Knuckle shaft
0.0.
Factory
spec.
24.948
to
24.980 mm
0.9822
to
0.9835 in.
Bushing 1.0.
Factory
spec.
25.020
to
25.053 mm
0.9850
to
0.9863 in.
D6-$
12
188


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kubota B1700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kubota B1700 in the language / languages: English as an attachment in your email.

The manual is 15,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kubota B1700

Kubota B1700 Installation Guide - English - 233 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info