583361
94
Zoom out
Zoom in
Previous page
1/153
Next page
9-11C
TIGHTENING TORQUES - ENGINE
Flange bolts - cylinder-head M 8 35 Nm (25 ft.lb)
Nuts-cylinder base M 10 35 Nm (25 ft.lb)
Flywheel collar nut M 12x1 60 Nm (44 ft.lb)
Nut for primary sprocket (LH thread) M 18x1.5 Loctite 243 150 Nm (110 ft.lb)
Nut for inner clutch hub M 18x1.5 Loctite 243 100 Nm (74 ft.lb)
Crankcase and cover bolts M 6 8 Nm (6 ft.lb)
Swingarm pivot M 14 100 Nm (74 ft.lb)
Flat head bolt release plate kickstarter M 6x16 Loctite 648 19 Nm (14 ft.lb)
Other bolts M 6 10 Nm (7 ft.lb)
M 8 25 Nm (19 ft.lb)
M 10 45 Nm (33 ft.lb)
Piston fitting clearance 0.05 mm (250) 0.06 mm (300) 0.08 mm (380)
Piston ring end gap 0.30.4 mm
Connecting rod bearing - radial clearance 0.0210.032 mm
Transmission shafts end float 0.1 0.2 mm
Clutch springs - length Ø 2.5 new = 43 mm, minimum length = 42 mm
TOLERANCES AND FITTING CLEARANCES
GASKET THICKNESSES
Crankcase 0.5 mm
Clutch cover 0.5 mm
Cylinder bottom gasket as required
Available cylinder bottom gaskets 0.2/0.4/ 0.5 /0.75 mm
Cylinder-head gasket O-rings
250 SX 250 MXC, EXC
BASIC CARBURETOR SETTING
Keihin PWK 38 AG PJ
110499
172 (170,175)
48 (45,50)
85
NOZ E (NOZ F)
III
7
1,5
55
Keihin PWK 38 AG
130499
180 (178,182)
45 (48)
85
NOZ G (NOZ H)
III
6
1,5
300 MXC, EXC
Keihin PWK 38 AG
140499
175 (172,178)
45 (48)
85
NOZ H (NOZ I)
III
6
1,5
380 SX, MXC, EXC
Keihin PWK 38 AG
150499
170 (168,172)
45 (48)
85
NOZ H (NOZ I)
III
6
1,5
Carburetor
Carburetor setting number
Main jet
Idling jet
Starting jet
Jet needle
Needle position from top
Slide
Air adjustment screw open
Performance restrictor
Power jet jet
94


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for KTM 250 MXC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of KTM 250 MXC in the language / languages: English as an attachment in your email.

The manual is 0 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info