629288
71
Zoom out
Zoom in
Previous page
1/74
Next page
71
lares
programming manual
PROGRAMMING SUMMARY
This paragraph summarizes programming options that ensure the proper functioning of Panel based on the
parameters dened by the norms listed on page 73. If these programming data are changed the Panel shall
NOT be compliant with these norms.
PROGRAMMING ALARM, TAMPER AND FAULTS EVENTS
EVENT PROGRAMMING OUTPUTS SECTION
PROGRAMMING DESTINATIONS
SECTION
Zone alarm
Partition alarm
Select the output associated with
imago siren (or relay output if you
are using third-parts sirens)
Select at least one destination
present on phonebook
Zone tamper
Partition tamper
Panel tamper
Controlled output tamper
Peripheral tamper
Missing Peripheral
Select the output associated with
imago siren (or relay output if you
are using third-parts sirens). You
must also select 'When system
armed' in 'Activate output' section
(output activation is required only
for the GRADE 2)
Select at least one destination
present on phonebook
Masking/Zone faults
Missing net
Low battery
Missing Ethernet
Missing PSTN line
GSM trouble
Fuse protection
Power supply faults
Low power supply voltage
Battery faults
Communication faults
System reset
Is not allowed to activate no
acoustic signaling device.
Select at least one destination
present on phonebook
If you programmed Zone alarm events, you do not need to program the partition alarm, and vice versa.
Similarly should be programmed Zone tamper and Partition tamper events.
ARMING AND DISARMING OPERATIONS ALLOWED
All options that allow to arm and disarm the System without the use of an adequate level of access do not
conform. In particular, you cannot bind arming mode to zones programmed as 'Command' or keys on the
keypad that has enabled the 'No PIN' option.
ALARMS TRANSMISSION
GRADE 3
Events should be transmitted to the alarm receiving center exclusively through GPRS network (via gemino
Communicator-ATS4) or Ethernet (in case of IP Panel) with SIA DC-09 communications protocol. On the
contacts page can be programmed the IP receiver to be selected as a destination. To enable events
transmission on IP you must turn on the 'Enable events on IP' option. You also need to enable a supervision
by selecting 'Enable supervision' or programming the receiver as the destination on 'Periodic Test' event. The
'Periodic Test' period, to be set on the options page, must be less than 300 minutes.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ksenia Lares at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ksenia Lares in the language / languages: English as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ksenia Lares

Ksenia Lares User Manual - English - 40 pages

Ksenia Lares User Manual - English - 45 pages

Ksenia Lares Installation Guide - English - 17 pages

Ksenia Lares User Manual - German - 26 pages

Ksenia Lares Quick start guide - Dutch - 3 pages

Ksenia Lares User Manual - Dutch, French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info