693399

Ksenia Lares 4.0 Manual

34
Zoom out
Zoom in
Previous page
1/58
Next page
rev. 0/2018
lares 4.0 PROGRAMMING MANUAL
34
Output logic
In this section, the operating logic of the zone is set during the output time.
There are three modes:
1. Immediate: if violated during the exit time, the zone will generate an alarm.
2. Delayed: Select this option if you want the zone to generate no alarms during the exit time.
3. Last exit: It is the last zone of the exit path, when it is breached and then restored during the exit time, it
automatically resets the exit time. Always referring to figure a (Page 33), the zones marked with 1, 2 and 3 must be
marked as exit delay and number 1 as "last exit".
• Always active: if this option is selected, when the zone is breached, an alarm will be generated regardless of the
partitions associated to the zone (e.g. 24h zone)
• Bell: If this option is selected, when the zone is breached with the partitions disarmed, an audible signal will be
generated on the keypads having "bell sound signal" enabled and associated to the same partitions of the same zone.
Exclusion
It is possible to manage the exclusion of the zone with four different modes:
1. Not excludable: if this option is selected, the zone cannot be excluded by the user.
2. Excludable: if this option is selected, the zone can be excluded by the user. An excluded zone does not signal alarms.
Tampers and faults/masks will continue to be signalled unless the option "also exclude zone tamper" is enabled.
3. Self-exclusion: if this option is selected, the zone is automatically excluded if it is breached at the time of arming. The
self-exclusion never excludes tampers and maskings unless the option "also exclude tamper zones" is enabled. The
zone is automatically rearmed in the next disarming.
4. With reinclusion: if this option is selected, the zone is automatically excluded. If it is breached at the time of arming,
as soon as it returns to the resting status, it is automatically rearmed.
Balancing
Each control panel board has 8 inputs and 2 programmable I/O terminals that can be configured as inputs or outputs
(practically, on the control panel board, we already have up to 10 inputs).
Both on the control panel and auxi module, each input can be programmed into eight different types of balancing.
The following table shows how the lares control panel interprets the resistance values for different balancing
configurations and their associable conditions:
1. Normally closed:
Band 0 Band 1 Band 2 Band 3 Band 4
0-1.8KΩ 2.2-4.1KΩ 4.2-6.8KΩ 7.2-14KΩ ∞ (open)
Resting Alarm
2. Normally open:
Band 0 Band 1 Band 2 Band 3 Band 4
0-1.8KΩ 2.2-4.1KΩ 4.2-6.8KΩ 7.2-14KΩ ∞ (open)
Alarm Resting
… 34 …


Need help? Post your question in this forum.

Forumrules
1

Forum

ksenia-lares-4.0

Reset search

  • Hi
    We have a message peripherals lost. What does this mean? Submitted on 24-7-2021 at 08:15

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ksenia Lares 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ksenia Lares 4.0 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info