693400
3
Zoom out
Zoom in
Previous page
1/10
Next page
EN
3
FUNCTIONS
Display of system status
Display of functioning parameters ( date/time, active GSM network, GSM level, etc)
System commands (complete or partial arming, reset, activation of outputs terminals, phone calls,
etc.)
Full Programming of system parameters
Programming of local parameters (audio volume, backlight levels)
KP functionality exclusion for front cleaning purposes
Remote Listening
Vocal messages recording
RFID/NFC
Tag reading to arm and disarm the intrusion detection systems set up with the lares
devices.
OPTIONALS
KSI7500000.000 / KIT 1,5 m. cable for GSM/GPRS programming
KSI2100001.300 / Table sustainer
KSI2100002.300 / KIT ergo keypad
INSTALLATION
BUILT-IN INSTALLATION (WITH DIN 503 BOX) OR DIRECTLY ON THE WALL
INSTALLATION WITH TABLE SUSTAINER
The keypad ergo can be installed directly on a wall or put in an DIN 503 box set in the wall or leant on a
plain surface by means of the proper sustainer.
1. Push the cable through to the proper opening.
2. Fix the keypad base to the DIN 503 box with the supplied screws opening the proper eyelets. To x
the keypad base directly to a wall, use proper plugs (not supplied) through the proper eyelets.
3. Connect the cables to the terminals on the rear of the keypad.
4. Fit in the PCBA on the left side of the keypad base, keeping the display in the front and the clamps
on the back, then press the right side until a double-click is heard.
5. Insert a coloured Lexan at choice into the cover.
6. Close the cover properly.
1. Install, with a light pressure, the part 1 of the table sustainer on the back of the keypad base.
2. Fit in the part 2 of the sustainer on the part 1 by the mean of the proper hinge.
3. Push the cable through to the proper opening.
4. Connect the cables to the terminals on the rear of the keypad.
5. Fit in the PCBA on the left side of the keypad base, keeping the display in the front and the clamps
on the back, then press the right side until a double-click is heard.
6. Insert a coloured Lexan at choice into the cover.
7. Close the cover properly.
8. Use the optional cable for the programming of the communicator GSM/GPRS gemino.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ksenia Ergo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ksenia Ergo in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info