507882

Krups XP 1500 Manual

12
Zoom out
Zoom in
Previous page
1/15
Next page
15
to come out of the steam nozzle. Proceed
with steps 4.a) and 4.b) in the section
« Making Cappuccino ».
5.When all steam is released, close the steam
release knob and turn off the machine.
Caution :
If you do not need all the water for
steaming, proceed as follows:
a) turn off the machine.
b) release the remaining steam pressure into
another container.
Do not close the steam release knob
before all steam is released or machine
has been turned «off»! (See section –
CAUTION - PRESSURE)
ATTENTION !
The plastic housing of the cappuccino nozzle
(e4) has 2 fine holes on sides which draw air
into the milk.
If those holes get clogged, the milk will not be
frothed properly. Therefore, do not dip the
cappuccino nozzle in milk or froth up to those
holes.
Cleaning the espresso and
cappuccino side
Before cleaning, turn «off» the machine,
unplug it, and allow it to cool down.
The filter holder, filter basket, carafe, carafe lid
and overflow lid must not be cleaned in dish
washer. Only use hot water and gentle soap.
Never use abrasive materials.
The machine can be wiped clean by using a
damp cloth. Never immerse the body of your
«appliance» in water or any other liquid.
Clean the brewing head with a damp cloth
and remove ground coffee. If there is water
left in the boiler chamber, let the machine
cool down, remove all those parts and empty
through the top opening by turning upside
down.
Cleaning the Cappuccino nozzle
Clean the steam nozzle each time after you
have immersed it in the milk, otherwise the
inside of the nozzle becomes clogged and the
milk deposits on the outside harden and
become difficult to remove.
If clogging does occur, remove the plastic
housing of the cappuccino nozzle (22) once
appliance is cold and then unscrew the tip of
the steam nozzle (23).
Remove all milk particles using a sewing
needle and rinse under the faucet. Replace
nozzle tip making sure to screw it on tightly.
Wipe off the outside of the nozzle with a wet
cloth. Hold the wet cloth very close to the tip
of the nozzle and open the steam valve. Let
the steam escape into the wet cloth for one or
two seconds, then close the valve. Any milk
residue will then be flushed out. The plastic
housing of the cappuccino nozzle should be
rinsed in warm water. If the small suction
openings are clogged up, it can be opened
with a small needle.
Cleaning the drip tray
The overflow grid and the cavity under he
grid can be cleaned by removing the grid
(24).
CAUTION
Do not try to open or disassemble the
main body of the machine.
Decalcifying the
espresso side
The warranty does not cover faulty or
broken espresso machine due to not
being descaled.
• Due to the acid substance, we recommend
protecting your worktop and sink unit
during the descaling process, especially if it
is made of marble or stone. Isolate your
espresso with a tea towel, a tablecloth or a
tray.
The espresso machine must be decalcified
regularly. The frequency depends on the
hardness of your water and how often you
use the espresso machine.
Before descaling, the brewing sieve on the
brewing head must first be screwed off.
1.Remove all lime and coffee residues from
the brewing sieve and the brewing head.
2.Remove the plastic housing of the cappuc-
cino nozzle (22).
As descaling agent we recommend the use of
reference solution N°F054 from Satisfusion 1
Service at 888-344-0727.
XP1500/1530 US/F/E.PM6.5 16/03/05, 10:5215
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Krups XP 1500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Krups XP 1500 in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info