Manual Krups EVIDENCE EA8908 (page 25 of 306) (All languages)

672684

Zoom out

Zoom in

1/306

Installing the cartridge in the appliance: Screw the lter cartridge into the bottom of the water tank using the

accessory supplied with the cartridge. Fig. 4

Set the month when the cartridge is tted (position 1 on the illustration, left side gure in the opening) by turning the

grey ring located on the upper end of the lter. The month when the cartridge should be replaced is indicated in position

2 on the illustration. Fig. 5.

Put a container of 0.6 l under the steam exit. Fig. 6.

The machine must be primed whether the lter has been installed or not. This means that the water circuits have to

be lled. To do this, follow the instructions provided on the screen. The machine will begin by lling the water circuits,

preheating the circuits and then will complete an automatic rinse.

The screen will inform you when installation is complete.

Water hardness

You must set your machine depending on the hardness of your water, from 0 to 4. To do this, follow these instructions:

Before using the appliance for the rst time, check the hardness of your water so that you can set the appliance

accordingly. This operation should also be carried out when you use your machine in a place where the hardness of

the water is different or if you notice a difference in the hardness of the water. To check the water hardness, use the

test strip supplied with your machine or contact your local water authority.

The details of the classes are given in the table below:

Degree of hardness

Class 0

Very soft

Class 1

Soft

Class 2

Average hardness

Class 3

Hard

Class 4

Very hard

° dH < 3° > 4° > 7° > 14° > 21°

° e < 3,75° > 5° > 8,75° > 17,5° > 26,25°

° f < 5,4° > 7,2° > 12,6° > 25,2° > 37,8°

Appliance setting 0 1 2 3 4

Fill a glass of water and insert a strip. Fig. 2

After 1 minute read the level of water hardness. Fig. 3

Indicate the number of red zones when conguring the appliance.

Preparing the appliance

Remove and ll the water tank. Fig. 7.

Replace the water tank. Fig. 8.

Remove the lid of the coffee bean container and add coffee beans (max. 250 g). Fig. 9.

Replace the lid of the coffee bean container. Fig. 10.

BEFORE PREPARING DRINKS

IMPORTANT INFORMATION

Depending on the drinks chosen, your Espresso Automatic EA89 will automatically adjust the quantity of ground coffee.

Preparing the grinder

You can adjust the strength of your coffee by adjusting how nely the coffee beans are ground. In general, the ner the

coffee is ground, the stronger and creamier the coffee will be. It may also vary according to the type of coffee used.

We recommend a ne setting for espressos and a coarser setting for coffees.

Adjust the neness of grinding by turning the coffee grounds neness adjustment knob (J) which is located in the

coffee bean container. This setting should be applied during grinding notch by notch. After 3 rounds, you will notice a

pronounced difference in taste.

Setting the neness of grinding is useful when you change the type of coffee or if you want to make coffee that is more

or less strong. However, it is not advised to use this setting systematically.

Adjusting the coffee outlet

For all the drinks available, you can lower or raise the coffee outlets according to the size of your cup or glass. Fig.11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Krups EVIDENCE EA8908 in the language / languages: All languages as an attachment in your email.

The manual is 2,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Krups EVIDENCE EA8908 Manual

Product: