672690

Krups EVIDENCE EA8901 Manual

31
Zoom out
Zoom in
Previous page
1/306
Next page
29
EN
!
Important: If there is a power failure or if you unplug your machine, the cycle will continue from the current phase
when the power is returned. It will not be possible to cancel this operation. Complete the full cycle in
order to remove all of the descaling product which is harmful to health.
TROUBLESHOOTING
If one of the problems described in the table persists, contact KRUPS customer service.
PROBLEM CORRECTIVE ACTION
The machine displays a failure,
the software hangs or your
machine has a malfunction.
Switch off and unplug the appliance, remove the lter cartridge, wait for one
minute and start the appliance again.
Press and hold the on/off button for at least 3 seconds for starting.
The appliance does not switch
on when the ON/OFF button is
pressed (for at least 3 seconds).
Check your fuses and plug sockets.
Check that the two power plugs are correctly inserted into the socket.
The coffee grinder makes a
strange noise.
There is a foreign body in the grinder.
Contact the KRUPS Customer Service team.
The One Touch Cappuccino
block does not suck the milk.
The One Touch Cappuccino
blocks produces little or no froth.
Check that the block is assembled correctly (in particular the connector in the
milk tube).
Ensure that the steam nozzle is not blocked. If this is the case, see below “The
steam nozzle on your machine seems to be partially or completely blocked”.
Check that the connector is not blocked or dirty; soak it in a mixture of hot water
and washing-up liquid, then rinse and dry before reassembling.
Ensure that the exible pipe is not blocked or twisted and that it is properly inserted
into the One Touch Cappuccino block in order to avoid any air leaks. Check that
it is fully immersed in the milk.
Rinse and clean the block (see chapters concerning rinsing and cleaning the One
Touch Cappuccino block).
For milk drinks, we recommend that you use fresh, pasteurised or UHT milk which
has been recently opened. It is also advisable to use a cold container.
The steam nozzle on your
machine seems to be partially or
completely blocked.
Dismantle the nozzle from its support using the dismantling key. Fig. 31.
Replace the support without the nozzle: Fig. 32.
Start the rinse cycle for the One Touch Cappuccino block to remove any
remaining deposits.
Clean the steam nozzle and ensure that the opening of the nozzle is not
obstructed by the remains of milk or limescale. Use the cleaning needle if
necessary. Fig. 33
No steam comes out of the
steam nozzle.
Ensure that the steam nozzle is not blocked. See “The steam nozzle on your
machine seems to be partially or completely blocked.” below
If this does not work, empty the water tank and remove the Claris cartridge
temporarily. Fill the water tank with mineral water with high calcium content
(>100 mg/l) and run steam cycles (5 to 10) consecutively into a container until
you obtain a continuous jet of steam.
Put the cartridge back in the tank.
Steam is leaking from the drip
tray grid.
Depending on the type of preparation, steam may escape from the drip tray
grid.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Krups EVIDENCE EA8901 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Krups EVIDENCE EA8901 in the language / languages: All languages as an attachment in your email.

The manual is 2,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info