Manual Krups Essential EA816 (page 17 of 74) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

807147

Zoom out

Zoom in

1/74

If one of the problems described in the table persists, contact KRUPS customer service.

PROBLEM MALFUNCTION CORRECTIVE ACTION

Your machine detects a fault:

a symbol appears.

Switch off and disconnect the machine, remove the filter cartridge, wait for a

minute and restart the machine.

The appliance does not turn

on when the button is

pressed.

Check your fuses and plug sockets.

Check that the two power plugs are pushed in properly both on the appliance

and at the socket.

The coffee grinder makes a

strange noise.

There is a foreign body in the grinder. Disconnect the machine before inves-

tigating.

See if you can extract the foreign body using your vacuum cleaner.

The steam nozzle makes a

noise.

Check that the steam nozzle is correctly attached to its corresponding end

piece.

The steam nozzle on your

machine seems partially or

completely clogged.

Ensure that the opening in the end piece is not obstructed by milk residue or

limescale. Unclog the holes with the needle supplied with your appliance.

The steam nozzle makes little

or no milk froth.

For milk-based drinks, you use very fresh, very cold pasteurised or UHT milk.

It is also advisable to use a cold container. If the results do not improve, try

changing the brand of milk.

No steam comes out of the

nozzle.

Empty the tank and temporarily remove the filter cartridge. Fill the water tank

with mineral water which is high in calcium (> 100 mg/l) and run successive

steam cycles.

The auto-cappuccino setting

makes little or no froth.

The auto-cappuccino setting

does not take in milk.

Check that the accessory is correctly attached to the appliance, remove it

then replace it.

Check that the flexible tube is not obstructed or pierced and that it is correctly

attached to the accessory so as to make it airtight. Rinse and clean the ac-

cessory (refer to the “Auto-cappuccino accessory” chapter).

There is water underneath the

appliance.

Before removing the water tank, wait for 15 seconds after the coffee has fini-

shed flowing so that the machine finishes its cycle properly.

Check that the drip tray is correctly positioned on the machine; it should

always be in place, even when the appliance is not in use.

Check that the drip tray is not full.

The drip tray should not be removed during a cycle.

After emptying the coffee

grounds collector, the warning

message is still displayed on

the screen.

Correctly replace the coffee grounds collector and follow the instructions on

the screen.

Wait at least 8 seconds before replacing them.

TROUBLESHOOTING

SETTINGS

All of the following options allow you to run the selected programs:

SETTINGS

You can set your water hardness between 0 and 4 by

pressing the + or – buttons . See “Measuring water

hardness” (below)

You can program automatic rinsing each time the appliance is

turned on by pressing the buttons and selecting ON.

You can choose the period after which your appliance will turn off

automatically (between 15 and 120 minutes by pressing the

buttons).

You can adjust the temperature of your coffee to three different

levels by pressing the buttons.

Return to coffee types menu.

Measuring water hardness

It is advisable to adjust the appliance according to the hardness of the water used. To check the water hardness, use

the stick supplied with your machine or contact your local water authority.

Degree of

hardness

Class 0

Very soft

Class 1

Soft

Class 2

Average hardness

Class 3

Hard

Class 4

Very hard

° dH < 3° > 4° > 7° > 14° > 21°

° e < 3,75° > 5° > 8,75° > 17,5° > 26,25°

° f < 5,4° > 7,2° > 12,6° > 25,2° > 37,8°

Appliance

settings 0 1 2 3 4

Installing the filter (Claris - Aqua Filter System cartridge) (32)

Note : To correctly install your cartridge, ensure that you follow the installation procedure each time you replace it.

(33) A mechanism which memorises the month in which the cartridge was changed and replaced (after a maximum

of 2 months): set the date using the cartridge cursor. Fit the cartridge in the tank (34). In the maintenance and settings

menu , the function indicator is located above the maintenance button . Using the navigation button ,

select the filter cartridge installation symbol . The symbols and the start button start to flash.

Place a 0.6 L container under the steam nozzle.

Press start . The start-up cycle begins and finished when the coffee types menu appears

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Krups Essential EA816 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1.98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Krups Essential EA816 Manual

Product: