Manual Krups EA815 (page 27 of 144) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

711474

Zoom out

Zoom in

1/144

■A screen indicates that the appliance is heating up. Once the appliance has finished heating up, you can begin to

make steam by pressing START , and following these steps (13):

Step 1: holding the milk jug in place, insert the steam nozzle approximately 2 cm into the milk and wait for it to

start frothing.

Step 2: raise the container slightly (approximately 1 cm). Do not completely submerge the metal tube.

Step 3: gradually lower the container as the froth accumulates. (14)

■When you have frothed the milk enough, press the STOP button to stop the cycle. Warning: the cycle does not

stop immediately.

■To remove any milk traces from the steam nozzle, place a container under the nozzle and start the steam function

again (approximately 10 seconds).

■The steam nozzle is removable in order to allow for deep cleaning. Wash it with water and a little non-abrasive

detergent using a brush. Rinse and dry (15-16). Before replacing, make sure that the air holes are not clogged with

milk residue. Unclog the holes with the needle supplied with your appliance if necessary (17).

■To stop the steam, press the STOP button .

WARNING: THE CYCLE DOES NOT STOP IMMEDIATELY.

Steam can be produced for a maximum of 2 minutes per cycle.

Auto-cappuccino XS 6000 set (sold separately)

■This auto-cappuccino accessory enables you to make cappuccinos or lattes (18). Connect the different parts to

each other. Ensure that the pipe is not pierced by keeping the knob in the correct place.

■After removing the lid, fill the jug with milk (19) and place a cup or glass under the auto-cappuccino nozzle (20).

Select cappuccino or latte on the special nozzle (21).

■Start steam, as indicated in the chapter Making drinks with steam.

■Once you have made the milk froth, place your cup under the coffee jets and start a coffee cycle (22).

To prevent the milk from drying on the auto-cappuccino accessory, ensure that you clean it thoroughly. You are advised

to wash it immediately by running a steam cycle with the accessory jug filled with water in order to clean the inside

of the nozzle. For this you can use the KRUPS liquid detergent available separately.

Emptying the coffee grounds collector and the drip tray

■If the symbol starts flashing, empty and clean the drip tray (the drip tray may contain coffee grains) and the coffee

grounds collector (23-25).

■The drip tray is fitted with floats which indicate when it needs to be emptied (26). Once you have removed the coffee

grounds collector, you should empty it completely in order to avoid any overflow.

■The warning message will continue to be displayed if the coffee grounds collector is not pushed in or inserted

correctly (24). You cannot make an espresso or a coffee while the warning message is shown.

Rinsing the circuits :

Press the maintenance and settings button (27). The function indicator is shown above the maintenance button

If necessary, using the navigation button, select the rinse symbol .

Press START , rinsing starts and finishes when the coffee menu appears.

MAINTAINING YOUR APPLIANCE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Krups EA815 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Krups EA815 Manual

Product: