Manual Krups EA80 serie - ESPRESSERIA AUTOMATIC (page 22 of 156) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

690027

Zoom out

Zoom in

1/156

4. Info (number of cycles)

The light comes on.

To go to the next stage, press the button. You will go back to adjustment 1.

To leave settings mode, press .

At any of these stages, you can leave settings mode by pressing the button if you have nished your adjustments. All

of the lights will go off. These settings stay applicable even if there is an electric power cut. You can change these settings

at any time by repeating these operations.

TROUBLESHOOTING, CORRECTIVE ACTIONS

PROBLEM MALFUNCTION CORRECTIVE ACTION

Your appliance detects a fault.

Switch off and disconnect the appliance, remove the l-

ter cartridge, wait for a minute and restart the appliance.

The appliance does not turn on when the button is

pressed.

Check your fuses and plug sockets.

Check that the two power plugs are correctly pushed in

the socket.

The coffee grinder makes a strange noise.

There is a foreign body in the grinder. Disconnect the

appliance before investigating. See if you can extract

the foreign body using your vacuum cleaner.

The steam nozzle makes a noise.

Check that the steam nozzle is correctly attached to its

corresponding end piece.

The steam nozzle on your appliance seems partially or

completely clogged.

Ensure that the opening in the end piece is not ob-

structed by milk residue or limescale. Unclog the holes

with the needle supplied with your appliance.

The steam nozzle makes little or no milk froth.

For milk-based drinks, use very fresh, very cold pas-

teurised or UHT milk. It is also advisable to use a cold

container. If the results do not improve, try changing the

brand of milk.

No steam comes out of the nozzle.

Empty the tank and temporarily remove the lter car-

tridge. Fill the water tank with mineral water which is

high in calcium (> 100 mg/l) and run successive steam

cycles.

The auto-cappuccino set makes little or no froth.

The auto-cappuccino set does not take in milk.

Check that the accessory is correctly attached to the

appliance, remove it then replace it.

Check that the exible tube is not obstructed or pierced

and that it is correctly attached to the accessory so as

to make it airtight. Rinse and clean the accessory (refer

to the “Auto-cappuccino accessory” chapter).

There is water underneath the appliance.

Before removing the water tank, wait for 15 seconds

after the coffee has nished owing so that the appli-

ance nishes its cycle properly.

Check that the drip tray is correctly positioned on the

appliance; it should always be in place, even when the

appliance is not in use.

Check that the drip tray is not full.

The drip tray should not be removed during a cycle.

Clean the tank and its connection regularly to avoid the

build up of scale, which can cause leaks.

After emptying the coffee grounds collector, the warning

message is still displayed on the screen.

Remove the coffee grounds collector and ensure it is

empty and clean. Wait at least 6 seconds before replac-

ing, and ensure it is correctly installed.

my Krups EA80 is less than a year old and now the coffee has almost no crema Submitted on 27-5-2022 at 12:14
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Krups EA80 serie - ESPRESSERIA AUTOMATIC in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Krups EA80 serie - ESPRESSERIA AUTOMATIC Manual

Product: