818705

Kress KR174E Manual

12
Zoom out
Zoom in
Previous page
1/156
Next page
12
EN
1
2
Usually your MissionTM RTKn's blades need to be reversed each month and replaced every week, you can
adjust the frequency of replacing the blade according to the cutting quality of the lawn. When replacing the
blades, make sure to replace all of them at the same time. You can replace them with one of the spare blade
kits and extra blade screws supplied with your MissionTM RTKn.
Before attempting to replace your MissionTM RTKn’s
blades, turn the power off and put on protective gloves
and follow these steps:
1. Gently flip the MissionTM RTKn over.
2. Remove the battery cover and remove the battery.
3. Take the screws off the blades with a screwdriver.
4. Firmly screw on the new blades.
5. Refit the battery and the battery cover.
If your MissionTM RTKn has dual-layer blades, follow
these steps to replace:
1. Turn off and gently flip the MissionTM RTKn over.
2. Remove the battery cover and remove the battery.
3. Take the 3 screws for fixing disk off with a hexagon
screwdriver.
4. Remove the disk.
5. Take the 6 screws for fixing blades off with a
screwdriver and remove the blades.
6. Firmly screw on the new blades and new screws for
fixing blades.
7. Refit and firmly screw on the disk on the underside
of MissionTM RTKn.
8. Refit the battery and the battery cover.
Important: After screwing the blade to the blade
disc, make sure the blade is able to spin freely.
A. Replace the blades
The
MissionTM RTKn
does not cut grass like other
mowers. Its cutting blades are razor sharp on 2 edges
and rotate in both directions for maximum cutting
capacity. Redesigned blade profile better prevents grass
clippings from getting caught in the gap between the
disc and the blade. And with new material, the service
life of each cutting blade will be longer than that of
other brands’ when it is programmed to mow every
day. Always check to see if the blades are chipped or
damaged and replace them if they are. When the cutting
blades are dull and worn out, they should be replaced
with the spare blades provided with your
MissionTM
RTKn
. Spare blades are also available at your nearest
Kress retailer.
1
WARNING: Before cleaning, adjusting, or replacing the blades, turn your Mission
TM
RTK
n
OFF
and put on protective gloves.
WARNING: When fitting new blades, make sure you replace ALL the blades. Always use new
screws when fitting blades. This is important to ensure blade retention and balance the blade
turning disc. Failure to use new screws could cause serious injury.
Keep it Sharp
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress KR174E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress KR174E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 17.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info