818717
15
Zoom out
Zoom in
Previous page
1/136
Next page
15
EN
Troubleshooting
If your MissionTM does not work correctly, follow the trouble shooting guide below. If the fault persists, contact
your dealer.
Symptom Cause Solution
The LED light on the charging
base does not turn on. There is no power.
Check the charging base is connected
properly to the charger and the charger
is connected to a suitable power supply.
Red light turns on the charging
base.
The boundary wire isn’t
connected.
Check that the boundary wire has been
connected correctly to the charging base.
Check there are no breaks in the
boundary wire, especially in the wire ends.
Your MissionTM is inside its
working area but the display
says “outside working area”
and the LED is green.
The boundary wire ends are
clamped incorrectly. Reverse the boundary wire ends.
MissionTM cannot correctly
dock with the Charging base.
Environmental influences. Restart MissionTM.
Poor connection caused by
debris on the charging strip.
Clean the contact pins located on the
charging base and the charging strip on
MissionTM using a cloth.
MissionTM runs outside the
boundary wire. MissionTM does
not mow an area within a
boundary wire zone. MissionTM
reverses or rotates erratically
near the boundary wire.
The boundary wire of another
MissionTM or another branded
robotic mower is positioned too
closely.
Ensure your MissionTM boundary wire
has at least 1m of spacing between the
neighboring boundary wire.
The boundary wire has been
installed with acute angles.
Check the boundary wire to ensure the
angles are smooth.
In wet conditions, the boundary
wire electric signal may leak
where wire has been joined or
repaired.
Check boundary wire joints. Insulate to
provide a fully waterproof connection.
There is boundary wire electric
signal leakage due to broken
insulation.
Repair damaged boundary wire
insulation with insulation tape.
The cutting area is larger than
the allowable cutting area for
MissionTM.
Decrease the cutting area.
MissionTM exits the boundary
wire due to high speed when
going down a hill.
The boundary wire is placed on
a slope steeper than 17% (1).
Reposition the boundary wire away from
slopes that are steeper than 17% (10°).
Environmental protection
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress KR122E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress KR122E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 17.04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info