813963

Kratki Zosia Manual

14
Zoom out
Zoom in
Previous page
1/136
Next page
14
EN
Preparation for installation
The replace insert is delivered ready to be built and installed. After unpacking, check the complete-
ness of the unit and make sure that the kit components have not been damaged during transport. In
selected replace inserts, the deector, handle, air damper handle and the rod handle used to adjust
the ue gas damper (shaft) should be installed.
In guillotine-type inserts, the screws locking the counterweight should additionally be removed. De-
pending on the model, check:
- the mechanism for adjusting the chimney draught (shaft),
- the mechanism for adjusting the air supply to the combustion chamber (ash drawer, air damper),
- the mechanism of operation of the front door closure (guides, hinges, handle),
- correctness of installation of ash pan/ash drawer and grate,
- the condition of the glass and the sealing cord of the re door,
- the condition of the ceramic lining of the rebox (selected replace inserts).
The inspection should be carried out in the presence of the installer. If you nd any damage or decien-
cies, please contact customer service. Before installing the replace insert, the chimney ue must be
expertly inspected and received for its technical parameters and condition - tightness, patency. Instal-
lation of the replace stove can be carried out after a positive result of the chimney sweep’s expertise
of the ue, and after checking the completeness of the device and the proper operation of all the
mechanisms mentioned above.
Location of the replace insert and connection to the chimney
The replace insert must be installed on a noncombustible oor with a minimum thickness of 30 cm,
and the oor at the replace door must be protected by a strip of noncombustible material with a
minimum width of 50 cm. The safe distance of combustible elements from the glass should be min.
150 cm (Fig. 1 b). Before installing the replace, it is also necessary to check the mechanical strength
of the oor on which the replace insert is to be placed, taking into account the total weight of the
insert and its housing.
The device should be located as close as possible to the ue pipe. When moving the replace, do not
grab the handle, as you risk damaging it. The appliance must be placed at a safe distance from any
ammable products. The ue under which the replace is connected should be airtight, smooth and
made of low heat-conducting materials. The connection between the chimney and the replace stove
must be made of non-ammable materials protected against oxidation (enamel or steel ue pipe).
Connection to a common chimney is possible.
When connecting to a common chimney, the door must always be closed. The pressure of the chimney
should be 12 Pa.
A diagram of an example installation and connection to the chimney is shown in Figure 1 a) ( 1 - -
replace insert, 2 - interior of the housing, 3 - decompression chamber , 4 - outdoor air intake duct,
5 - outdoor air intake, 6 - chimney, 7 - connector, 8 - ventilation grille, outlet, 9 - ventilation grille, inlet,
10 - layer of non-combustible material).
The appliance should be connected under a chimney section that provides a draught of 12 +- 2 Pa. If
the chimney produces a weak draught, consider laying new ues. It is also important that the chim-
ney does not produce excessive draught, in which case a draught stabilizer should be installed in the
chimney. Alternatively, special chimney endings equipped with an exhaust fan that regulates draught,
or other chimney attachments (e.g. a reman) may be used. Have your chimney ue inspected by a
master chimney sweep.
The room in which the device will be installed must have a volume resulting from the ratio of 4 m 3 x
1 kW of nominal thermal power of the device, but not less than 30 m3. In addition, it should have an
ecient ventilation system and provide the necessary amount of air required for the proper operation
of the cartridge. It is assumed that to burn 1 kg of wood in a replace with a closed combustion cham-
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kratki Zosia at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kratki Zosia in the language / languages: English, German, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 2.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info