Manual Kratki VNP (page 13 of 136) (English, German, French, Italian, Polish, Portuguese, Swedish, Spanish)

813960

Zoom out

Zoom in

1/136

INTRODUCTION

Thank you for trusting us and choosing our device. Our replace was made with your safety and com-

fort in mind. We are convinced that the commitment that has been put in

in the design and production process of the replace will be reected in the satisfaction with the cho-

ice made. Please read through all the chapters of this manual carefully before you begin installation

and use. If you have any questions or doubts, please contact our technical department. All additional

information is available at www.kratki.com.

Note

Requirements for the conditions and rules for installing replaces such as replace inserts can be fo-

und in the standards and regulations in force in each country. The national and local provisions conta-

ined therein should be observed! It is forbidden to make any modications

in the construction of the device. Kratki.pl Marek Bal shall not be liable for any damage caused by

improper installation and use of the replace insert.

Air replace inserts manufactured by Kratki.pl Marek Bal are convection heating devices classied as

xed replaces with manual fuel loading and lockable combustion doors.

These replaces are designed to be enclosed or built into a wall niche and are suitable for burning har-

dwood fuel. Our replace inserts comply with the PN-EN13229:2002+A1:2005+A2:2006 standard and

are CE marked. To avoid re hazards, the replace should be installed in accordance with local building

codes and the technical recommendations given in this manual. The installation design and installa-

tion of the insert should be carried out by a professional or qualied person. Before the appliance is

released for operation, a protocol technical inspection must be carried out, to which the opinion of the

chimney sweep and re specialist must be attached.

FUEL SELECTION

The manufacturer only allows the use of hardwood logs of the following types: beech, hornbeam, oak,

alder, birch, ash. It is assumed that 1 kg of wood with a moisture content of up to 20% yields 3 kW of

power. The moisture content of the wood used to re the device should not exceed 20%. The use of

logs with higher moisture content may cause the used insert not to achieve the technical parameters

declared by the manufacturer. It is not advisable to use coniferous logs for burning, as they cause

intense burning and make it necessary to clean the appliance and chimney ue more often. Do not

burn minerals (e.g. coal), tropical wood (e.g. mahogany), wood bark, chemical products or liquids such

as oil, alcohol, gasoline, naphthalene, laminated board, impregnated or compressed wood bound with

glue, garbage or other waste.

INSTALLATION OF A FIREPLACE INSERT

The installation of the replace insert must be carried out in accordance with the provisions of the

standards in force in this regard, the requirements of the construction law and the re safety standards

in force in this regard. Detailed regulations on construction safety, re safety and safety of use are

contained in the ordinances and building regulations of the country. Installation and commissioning

of the replace stove should be carried out by an installation company with the appropriate authori-

zation and experience for this purpose.

The installer should conrm in the warranty card the correct execution of the installation activities by

signing and stamping the warranty. If this requirement is not fullled, the Purchaser loses the right

under warranty claims against the replace stove manufacturer.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kratki VNP in the language / languages: English, German, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 2.4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kratki VNP Manual

Product: