813988

Kratki PATIO MINI Manual

32
Zoom out
Zoom in
Previous page
1/206
Next page
32
START-UP
Before using the device for the rst time, make sure that all the connections to the individual system
components have been made in accordance with the instructions in the manual. Incorrect connection
of the gas control system can result in its damage.
For the rst few starts, a specic smell can be detected, lasting up to several hours after use. This phe-
nomenon is related to the burning of paint. Animals may be particularly susceptible to the odours
generated during the paint burning. To speed up this process, it is recommended to warm up the
device to a maximum ame size for several hours.
INSTALLING THE GAS CONTROL SYSTEM
CAUTION!!!
This device and the gas control system can only be installed on factory settings. In the model con-
trolled by the remote control, do not install batteries in the receiver at this stage. Earlier connection
to the power source may damage the electronics of the system.
CAUTION!!!
The components of the gas control system should be installed in accordance with the instructions
in this manual.
Standard gas control system includes, depending on the option: the MertikMaxitrol GV32 or GV60
controller and the B6R-R8U receiver, in which the installed antenna enables wireless remote control.
System components should be installed in their designated areas. Changing their location may expose
the device to damage due to harmful temperatures or ooding.
The device can only work with the automation provided with the device. Connections of individual
components of the system have been made in such a way as to prevent them from being connected
improperly.
The remote control should not be more than 6-8 meters away from the device, in this instance,
after several hours (3-4 hours), the device will shut down automatically.
Connect the reducer to the cylinder making sure that the gaskets are in place (see the diagram above).
If the gaskets are shrivelled or damaged or if any of them are missing, the device cannot be used until
the gaskets are replaced. The valve must always remain/stay in a vertical position after each connec-
tion to the cylinder and throughout the lifetime of the device. Connecting the valve in a dierent
position results in cutting o the gas supply to the device and thus shutting down the device.
CAUTION!!!
The anti-tilt valve is a safety device against overturning of the device, so that when the device over-
turns, the valve automatically cuts o the gas supply to the controller and this extinguishes the ame.
Fig. 8.
CAUTION!!!
The connection to the gas source should only be made when the heater is o and the cylinder valve
is closed.
CAUTION!!!
It is forbidden to use open re during the process of installing or connecting the cylinder. Failure to
comply with the above may result in re, explosion and property damage, personal injury, or even
death.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kratki PATIO MINI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kratki PATIO MINI in the language / languages: English, German, French, Italian, Polish, Spanish, Finnish as an attachment in your email.

The manual is 4.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info