Manual Kratki ANTEK 8 (page 15 of 100) (English, German, French, Polish)

694592

Zoom out

Zoom in

1/100

1.Initial information

In some countries this appliance may not be the only source of heat for your building.

NOTE: To avoid the risk of re, the installation of this appliance should comply with all relevant

Health and Safety Regulations for your area and the Technical Instructions contained in this

manual. The design of the Fireplace and installation should be prepared by a qualied professional.

The chimney should be checked by a chimney sweep prior to the installation of the appliance.

Following the installation, both a technical and Safety test should be carried out on the unit and

signed o on by qualied specialists.

You are recommended to read carefully the whole of the manual to make the best of the replace

insert with water jacket and be satised with your purchase. The a user is liable for the results of the

failure to observe the guidelines of the assembly manual. It is recommended that you read the com-

plete manual carefully in order that you get the most out of your purchase. Failure to comply with the

guidelines in the manual leaves the owner/user liable.

The replace insert with water jacket should be installed in accordance with this operating manual.

Particular attention should be paid to:

- assembling the components of the replace insert with water jacket in accordance with their

intended use;

- connecting the replace insert with water jacket to the ue gas evacuation duct and the chimney

ue;

- providing required ventilation to the room where the replace insert with water jacket is installed;

- properly connecting the replace insert with water jacket to the central heating system and/or hot

water circulation system.

Detailed information related to installing the replace insert with water jacket is included in further

sections of this manual.

Requirements related to the conditions and principles of installations of such hearths as the replace

inserts with water jacket can be found in the standards valid in each country as well as in state and

local regulations. The provisions included in them must be observed.

Within the territory of Poland the following legislative acts are in force:

- the Regulation of the Minister of Infrastructure dated 12 April 2002 on tech- nical conditions that

buildings and their location should meet (Dz.U. no. 75 dated 15.06.2002 Chapter 4;

- PN-91/B-02413 standard Heat industry and heat engineering;

- PN-EN 13229:2002 standard Insert appliances including open res red by solid fuels. Requirements

and test methods; PN-EN 13229:2002/A1:2005 In- sert appliances including open res red by solid

fuels. Requirements and test methods;

- PN-EN 13229:2002/A2:2005 (U) Insert appliances including open res red by solid fuel.

Requirements and test methods

You are recommended to strictly observe the requirements included in the above regulations.

2. Intended use

Fireplace inserts with water jacket are designed to be red with deciduous wood. They are used to

heat ats and rooms where they are installed. They may be used as an additional source of heat. They

may also be used in conjunction with a storage water heater or may be used as a source of heating

for central heating.

The insert structure should be constructed in such a way so as to ensure assembly and disassembly

of the replace insert with water jacket without its destruction or damage. Moreover, it should ensure

the access of air necessary for burning and ventilation by the use of air grates on both sides of

a replace in the lower part of the insert structure and a bigger-sized outlet grate (in the upper part

of the housing) as well as constant access to operate a ue gases throttle or a chimney draft control-

ler (damper).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kratki ANTEK 8 in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 4,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kratki ANTEK 8 Manual

Product: