716909
12
Zoom out
Zoom in
Previous page
1/29
Next page
22 23
Functional details Functional details
Adjusting ignition electrodes
For a smooth ignition, the setting of the ignition electrode
must be controlled regularly.
Attention!
Immediately contact our service in case of recurrence.
Excess temperature sensor
As an additional safety device the high-pres-
sure cleaner is equipped with an excess tem-
perature sensor inside the chimney. Should
the safety devices as e.g. the float monitoring
device be defectice and the burner continues
to heat although the heating coil does not
conduct away heat a destruction of the
heating coil would be inevitable.
As soon as the temperature inside the
chimney exceeds 260 °C the excess tem-
perature release triggers and cuts out the
appliance. The display of the excess tempe-
rature sensor is located on the back of the
switchbox inside the high-pressure cleaner.
Trooble shooting excess temperature
see chapter „Small repairs - do it yourself!“
in these operating manuel.
Heat exchanger
The water is forced through a heating coil by the high-pressure pump.
The fuel pump sucks the fuel oil from the fuel tank via a fuel filter an and trans-
ports it to the injection nozzle. The heat exchanger is heated by a high-pressure
fan heater. A ventilator draws in the cold, fresh air from the bottom end of the
high-pressure cleaner and forces it upwards between the outer mantle and the
inner mantle. In the process, the fresh air is pre-heated and the outer mantle of
the heat exchanger is cooled.The pre-heated air is pressed through a mixing unit.
Here finely atomized fuel is injected via a nozzle and mixed with the air.
The electrodes located below then ignite the fuel-air mixture. The flame burns
from top to bottom, turns round and the hot gas flows past the heating coil
on its way back up. The burned gases collect in the exhaust chamber and are
emitted from the exhaust gas outlet.
1. Exhaust gas outlet
2. Mixing unit and nozzle
3. Electrodes
4. Inner cladding
5. Outer cladding
6. Fuel filter
7. Fuel pump
8. Heating coil
9. Fan
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kranzle therm-RP 1400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kranzle therm-RP 1400 in the language / languages: English as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kranzle therm-RP 1400

Kranzle therm-RP 1400 Additional guide - English, German - 17 pages

Kranzle therm-RP 1400 User Manual - German - 29 pages

Kranzle therm-RP 1400 User Manual - Dutch - 29 pages

Kranzle therm-RP 1400 User Manual - French - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info