508540
9
Zoom out
Zoom in
Previous page
1/31
Next page
16
Water and cleaning system
The water is fed to the high-pressure cleaner under pressure (2-8 bar pre-pressure). A
float valve regulates the water flow in the storage tank. Then the water is sucked directly
from the storage tank by the high-pressure pump and forced with the adusted pressure
through the heat exchanger to the safety spray lance. The high pressure jet is formed by
the nozzle at the end of the safety lance.
Environmental, refuse disposal and water protection regulations
must be observed!
Kränzle technology
Lance with trigger gun
The machine can only be operated when the safety trigger is squeezed. When the lever
is squeezed, the spray gun opens. The liquid is then pumped to the nozzle. The spray
pressure increases and quickly reaches the selected operating pressure. When the trig-
ger is released, the trigger gun closes and any further spraying of liquid from the lance is
stopped. The motor stops.
When actuating the gun once more the pressure control valve - safety valve closes and
the motor is started again. The pump resumes feeding water to the spraying lance with
the selected operating pressure. When the gun is closed, the water hammer opens the
pressure control valve - safety valve and the motor is switched off by the pressure
switch.
The trigger gun is a safety device. Repairs should only be performed
by qualified persons. Should replacement parts be required, use only
components authorized by the manufacturer.
Total stop system
The machine is fitted with a Total-Stop-System. If the gun is closed for longer than
approx. 20 seconds, the machine switches off automatically, after 20 minutes the
machine moves to safety switch off and you must use the main switch to turn it back on.
The machine restarts automatically when the gun is operated, provided that the master
switch is on.
17
High pressure hose and spraying device
The high pressure hose and spraying device supplied with the machine are made of high
grade material, they are also optimized for the machine and marked as required by the
appropriate regulations.
If replacement parts are required, only such parts that are authorized
by the manufacturer and which bear the markings required by the
appropriate regulations may be used.
The high pressure hose and spray device must be connected in a
pressure-tight manner.
The high pressure hose may not be driven over, pulled excessively, or
twisted. The hose may under no circumstances be pulled over sharp
edges, since otherwise the guarantee is automatically void.
Hoses are wearing parts. The guarantee only covers defects of
fabrication no external damages whatsoever.
Defective high-pressure hoses and spraying devices may not be
repaired. They always have to be replaced.
Pressure control valve-safety valve
The pressure control valve allows full adjustment of water quantity and pressure. The
safety valve protects the machine from excessive pressure and cannot be adjusted
beyond the admissible operating pressure. The setting nuts are sealed with lacquer
.
Replacements, repairs, new adjustments and sealing operations may
only be performed by trained personnel.
Adjustment of pressure, quantity and temperature
The operating pressure, the water flow
and correspondingly the water
temperature ist controlled by the pressure
control valve.
A right-hand turn increases the pressure, a
left-hand turn decreases the pressure.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kranzle Therm 602 E-M 24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kranzle Therm 602 E-M 24 in the language / languages: English as an attachment in your email.

The manual is 6,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kranzle Therm 602 E-M 24

Kranzle Therm 602 E-M 24 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info