508541
14
Zoom out
Zoom in
Previous page
1/31
Next page
26 27
Troubleshooting
Malfunction
Water supply
Water tank runs over.
Water tank does not fill completely.
Pump does not suck.
Test: check water and chemical
system for tightness.
High-pressure pump
Pump makes loud noises.
Operating pressure is not reached.
Water drops from the pump.
Oil drops from the transmission.
Pressure is too low.
Machine does not switch off
Test: Bridge pressure switch (red)
Appliance does not start or
stopps during operation
Cause of malfunction / remedy
Float valve is dirty or defective.
Float valve is defective. Water filter is dirty.
Insufficient water inlet quantity.
Valves stick or are dirty. Suction hose leaks.
Chemistry valve is open or leaks. Check hose clips
(connections). High-pressure nozzle is clogged.
Connect water inlet directly to the pump (2-8 bar
pre-pressure). Disconnect suction lines below the
pump
Pump sucks air. Check suction connections.
Check high-pressure nozzle. Check valves. Check
O-rings under valves. Check sleeves. Manometer
is defective. Unloader: check stainless steel seat
and ball. Check seals on the control piston.
Replace sleeves in the pump.
Replace O-rings.
Check oil seals (replace). Check plunger and plun-
ger guides. Check water supply, since water defici-
ency or air suction can cause damage to seals and
O-rings (chemistry valve leaks?)
Worn high pressure nozzle. Stainless steel seat,
ball, O-ring in unloader is dirty or defective.
Manometer is defective.
Check return body and O-ring in unloader of the
valve housing.
Check pressure switch (red). Check micro switch.
Check cable connections. Board is defective.
Check electricity supply. Check main switch.
Check cable connections. Check board.
Check pressure switch. Switch off by overcurrent
release.
Malfunction
Machine does not start
Electrical heating elements
Insufficient water temperature.
Leakage
Gun drips. High pressure hose drips.
Manometer indicates pressure, but no
water comes out of HP-hose.
Cause of malfunction / remedy
Check electricity supply.
Check main switch.
Check cable connections.
Board defective.
Check pressure switch.
Switch off by overcurrent release.
Check electricity:
- ON-OFF - Switch
- Contactor
- Flow monitoring device
Clean nozzle. Replace seals.
Replace O-ring below screwed connection.
Clean nozzle.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kranzle Therm 602 E-M 36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kranzle Therm 602 E-M 36 in the language / languages: English as an attachment in your email.

The manual is 6,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kranzle Therm 602 E-M 36

Kranzle Therm 602 E-M 36 User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info