Manual Kranzle Bully 1000 TST (page 8 of 19) (English)

716872

Zoom out

Zoom in

1/19

14 15

Required minimum quantity of water (see technical data).

If the metered quantity of water is too small, you have to use a dif-

ferent water connection, guaranteeing the necessary output. Lack of

water leads to an accelerated wear of the joints (no warranty).

Never let the high-pressure pump run dry for more than 60 seconds.

Water supply

Please pay attention to the regulations of your waterworks com-

pany! In accordance with DIN EN 61770, the high-pressure cleaner

may not be directly connected to the public drinking water supply

lines. A brief connection however is permissible according to DVGW

(German Association for Gas and Water Affairs) if a non-return val-

ve with tube ventilator (Kränzle order no. 41.016 4) is built into the

water supply. Once the water has passed through the non-return

valve it is no longer considered as drinking water. Also indirect

connection to the public drinking water supply lines is permissible

by way of free emission in accordance with EN 61 770; e.g. by using

a reservoir with a float valve. Direct connection to a non-drinking

water supply line is permissible.

Please note: Lack of water

Lack of water occurs more often than you

probably believe. The more powerful a high-

pressure cleaner is the greater is the danger

that a lack of water occurs. If there is only

an insufficient amount of water available,

cavitation (water-gas mixture) arises inside

the high-pressure pump, which is normally

noticed too late or even not at all. The high-

pressure pump will be destroyed. Please

check the available quantity of water by fil-

ling a bucket with liter scale for one minute.

Insufficient quantity of electricity

If there are too many collectors in your

proximity connected to the network at the

same time, the available voltage and the

current intensity may decline. Consequently

the motor of the high-pressure cleaner does

not start or even blows. The power supply

may also be insufficient if the power supply

cable is too long or too thin. If extension

cables are too long, this may lead to a volta-

ge drop causing malfunctions or start-up

difficulties.

Check the line fusing and have the voltage and the available current in-

tensity checked by an expert in case of uncertainty (see technical data).

Electrical connection

The high-pressure cleaner is supplied with a power supply cable. The mains plug

must be fitted to a standard grounded socket with a 30 mA residual current

operated device. Connection up to the mains must be carried out by a properly

trained electrician and must comply with the requirements of IEC60364-1. The

socket must be protected with a 16 A fuse on the mains side. When using an

extension cable, this must have an earthed lead which is properly connected to

the socket. The conductors in the extension cable must have a minimum cross

section of 1.5 mm². Plug connections must be of a spray-proof design, and may

not be located on a wet floor. For extension cables of more than 10 m in length,

the minimum cross-section must be 2.5 mm²! When using a cable drum, the

power supply cable always must be unwound all the way.

Functional detailsFunctional details

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kranzle Bully 1000 TST in the language / languages: English as an attachment in your email.

The manual is 5,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kranzle Bully 1000 TST

Kranzle Bully 1000 TST User Manual - German - 19 pages

Kranzle Bully 1000 TST User Manual - Dutch - 19 pages

Kranzle Bully 1000 TST User Manual - French - 19 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kranzle Bully 1000 TST Manual

Product: