508516
9
Zoom out
Zoom in
Previous page
1/48
Next page
9
Inbetriebnahme
Elektroanschluß
Die auf dem Typenschild angegebene Spannung muß mit der Spannung der
Stromquelle übereinstimmen.
Bei Verwendung eines Verlängerungskabels muß dieses einen Schutzleiter
haben, der vorschriftsgemäß an den Steckverbindungen angeschlossen ist.
Die Leiter des Verlängerungskabels müssen folgenden Mindestquerschnitt
haben: bei 18 kW - 4 mm
2
bei 24 kW - 6 mm
2
bei 36 kW - 10 mm
2
bei 48 kW - 16 mm
2
1. Hochdruckschlauch mit Spritzpistole und Lanze am Gerät verschrauben.
2. Wasseranschluß herstellen und Wasserhahn öffnen.
3. Stromanschluß herstellen.
4. Gerät bei geöffneter Spritzpistole einschalten und mit dem Wasch-
vorgang beginnen.
5. Betrieb des Gerätes als Kaltwasser - Hochdruckreiniger:
Zündung “AUS” - Drehthermostat auf 0° C.
6. Bei Verwendung als Warmwasser - Hochdruckreiniger:
Vorwahl der Wassertemperatur mit dem Thermostat min. 40° C.
Die Maschine wird mit einem Anschlußkabel ohne Netzstecker
geliefert. Der Anschluß muß mit Schutzleiteranschluß und FI -
Fehlerstrom - Schutzschalter 30 mA eingesteckt werden.
Der Anschluß ist netzseitig entsprechend den Angaben auf Seite
2 träge abzusichern.
ACHTUNG !!!
Zu lange Verlängerungskabel verursachen einen Spannungs-
abfall und dadurch Betriebsstörungen. Bei Verwendung einer
Kabeltrommel muß das Kabel immer ganz abgerollt sein.
Kurzbetriebsanleitung
Ist auch auf dem Gerät angebracht.
Hochdruckschlauchleitung und Spritzeinrichtung
Die zur Ausstattung der Maschine gehörende Hochdruckchlauchleitung und
Spritzeinrichtung sind aus hochwertigem Material und sind auf die Betriebs-
bedingungen der Maschine abgestimmt sowie vorschriftsmäßig gekennzeichnet.
Bei Ersatzteilbedarf sind nur vom Hersteller zugelassene und
vorschriftsgemäß gekennzeichnete Bauteile zu verwenden.
Hochdruckschlauchleitungen und Spritzeinrichtungen sind
druckdicht anzuschließen. Die Hochdruckschlachleitung darf
nicht überfahren, übermäßig gezogen oder verdreht werden.
Die Hochdruckschlauchleitung darf nicht über scharfe Kanten
gezogen oder geknickt werden, sonst erlischt die Garantie.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kranzle 900E - ST 48 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kranzle 900E - ST 48 in the language / languages: German as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info