570561
2
Zoom out
Zoom in
Previous page
1/36
Next page
2
Installation procedure
Step 1:
Invert the display and place it on a soft and fl at surface. Locate the mounting points on
the back of the display.
Many LCD manufacturers conform to VESA standards. The VESA standard defi nes
the physical mounting interfaces. The LCD mount conforms to VESA 75/100/200/400
patterns.
Plasma monitors come with a random set of holes.
Note! Do not over tighten the screws. This may cause damage to the display or
bracket.
Before you begin, determine the desired mounting location.
Step 2:
Assemble the wall plate using the hardware and wrenches provided.
Note! Tighten screws uniformly to prevent distortion that might affect the assembly
process. Do not tighten with excessive force. Failure to follow these instructions may
cause excessive stress to the screws, greatly reducing their strength.
Solid concrete wall assembly: Carefully inspect the area where the LCD\Plasma\
Projector mount is to be installed. Check for any damage or loose cement.
Caution! When drilling holes in a cement wall or wooden studs, be absolutely sure there
are no water pipes or electrical wiring behind the wall. Use the wall plate to mark the
positions of the drilling holes.
Drill holes 3” deep using a (10 mm) masonry drill bit. Insert the plastic anchors into the
hole and tap fl ush until the washer is even with the concrete surface. Place the back plate
onto the concrete surface and slowly tighten each nut onto its respective anchor.
Wood studs assembly:
Use a stud sensor (sold separately) to locate framing near the desired mounting position.
Note! Framing beams are typically 1-1/2”- 2” wide and spaced 16” on center. We
recommend locating more than one stud to fi nd a trend in stud spacing. Using a sharp
device penetrate the drywall to identify the true center of the stud. Using the wall plate
base as a template, position the wall plate base vertically. Mark the hole position on
the wall, making sure you use the center screw holes. Use a level to check horizontal
alignment of marks.
Step 3:
For tilting models, gently pull the left and the right upper edges of the display to extend
the mount to its desired display tilting angle. Using a Phillips screwdriver, adjust the tilt
mechanism to its desired position. LCD mount models are designed to maintain their
tilting angle by using fi nger tips on the back of the monitor. Keeping the display far from
the tilting mechanism, turn the Philips screw to its desired angle.
Step 4:
Once the mounting of the display is completed, you can tills move the display from side to
side to optimize the fi nal position of the display. Gently slide the unit from left to right over
the steel rods on the wall plate.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic TVS-KN-AVS500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic TVS-KN-AVS500 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Konig Electronic TVS-KN-AVS500

Konig Electronic TVS-KN-AVS500 Installation Guide - All languages - 1 pages

Konig Electronic TVS-KN-AVS500 User Manual - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info